GT1020-LWDW-C Manual MITSUBISHI touch screen GT1020-LWDW-C MES Interface Function Manual

15 inches /10.4 inch /8.4 inch /12.1 inch with.
GOT front USB interface with protective cover (for replacement).
Applicable models: GT27, GT25. Cable length: 3m.
For connection between QnA/A/FXCPU (D-SUB25 pin connector) and GOT.
Connection between serial communication unit (AJ71QC24-R4) and GOT.
Applicable models: GT10, GT21 MITSUBISHI touch screen MES Interface Function Manual . For analog RGB output 1ch (slim module) GT1020-LWDW-C
Applicable model: GT27. Series introduction: set a number of basic functions in a small body model.
Screen size: 3.7 inches.
Display color: monochrome.
Mounting type: panel mounting type.
Resolution: 288 * 96.
Display device: STN monochrome.
Host frame color: white.
Power type: DC24V.
Communication interface: with built-in RS-232 MITSUBISHI touch screen MES Interface Function Manual .
Set a number of basic functions in a compact type.
GT1055/GT1050/GT1045/GT1040:
User storage capacity: 3MB.
Device USB port.
The standard RS-422/485 and RS-232 interface.
GT1030/GT1020:
User storage capacity: 1.5MB (gt1030) /512kb (gt1020).
Three color LED backlight design, equipment status at a glance.
The standard RS-422/485 or RS-232 interface.
Touch screen, also known as touch screen, touch panel, is a kind of induction type liquid crystal display device can receive contacts and other input signals,
When touching the screen button on the screen,
The tactile feedback system on the screen can drive various connecting devices according to the pre programmed program,
Can be used to replace the mechanical button panel, and by the liquid crystal display screen to create the image of the effect of birth MITSUBISHI touch screen MES Interface Function Manual GT1020-LWDW-C MES Interface Function Manual GT1020-LWDW-C MES Interface Function Manual . Cable length: 3m.
For connection between FXCPU (MINI-DIN8 pin connector) and GOT.
Connection between FXCPU communication function extension board (MINI-DIN8 pin connector) and GOT.
Applicable models: GT10, GT21. Protective film for 5 GT1020-LWDW-C MES Interface Function Manual . 7 inch screen (for HandyGOT).
Scrub (frame: white), 5.
Applicable model: used for hand held GOT GT11. The control cabinet for additional positive CF port (B disk).
Applicable models: GT16, GT15. "A series of high performance models that are widely used in network or single machine work environments.
Screen size: 5.7 inches.
Display color: 256 color or more color.
Mounting type: panel mounting type.
Resolution: QVGA (320 x 240).
Display device: STN color.
Host frame color: black.
Power type: DC24V.
Communication interface: with built-in RS-422.
Ideal model for high performance in a network or independent operation environment.
User storage capacity: 9MB (GT15__-VNB_:5MB).
Device USB port.
Standard RS-232 interface.
Support video /RGB unit.
If the capacitive touch screen is in the middle of the operation, the display resolution or display mode of the touch screen is changed again,
Or the refresh rate of the touch screen controller is adjusted by itself, and the cursor and the touch point can not be felt when the cursor is not corresponding to the touch point,
Must be re calibrated to the touch screen system. GT1020-LWDW-C Manual .
In order to ensure the normal operation of the touch screen system, in addition to ensure the proper installation of the system software,
Must also remember that in a host do not install two oor more than two kinds of touch screen driver,
This will cause the system to run in conflict, so that the touch screen system can not be used properly MITSUBISHI touch screen MES Interface Function Manual .