LK Automation Limited
Home >> Download >> MITSUBISHI >> Manual Download >> MITSUBISHI AJ35TJ-8D Manual AJ35TJ-8D User's Manual

MITSUBISHI AJ35TJ-8D Manual AJ35TJ-8D User's Manual

Product model: AJ35TJ-8D
Name: I/O MODULE
Brand: MITSUBISHI
Sort: User's Manual
File language: English
File size: 6.99MB
Input type: DC input, positive public end / negative public end.
Input points: 16 points.
Enter the response time: 0.2ms the following.
Rated input voltage / current: DC24V/5mA.
Output form: transistor output, leakage type.
Output points: 16 points.
OFF leakage current: 0.1mA.
Output protection function AJ35TJ-8D User's Manual.
Rated load voltage / current: DC12V/DC24V/0.1A.
External connection: 1 line /1 line type AJ35TJ-8D
40 pin connector type (FCN connector type).
Through the 40 pin connector type (FCN connector type) can be connected to a variety of devices.
Can be installed along the 6 direction.
Hardware simulation method is to use a number of hardware equipment to simulate the generation of the signal,
The signals are connected to the input end of the PLC system in a hard wired way, and the timeliness is strong AJ35TJ-8D User's Manual.
Software simulation method is in the MITSUBISHI PLC in the preparation of a set of simulation program,
The simulation provides the field signal, which is simple and easy to operate, but it is not easy to guarantee the timeliness.
Simulation of the process of debugging, debugging method can be used to segment, and the monitoring function of programmer AJ35TJ-8D User's Manual. A65B/A68B/A55B/A58B connection cable.
Length: 400mm. Long distance bus connection for QnA/ACPU.
Applicable models: GT16, GT15, GT11. Output points: 16 points.
Voltage: DC24V/AC240V, 2A/1 point, 16A/ all points.
OFF leakage current: 0.1mA.
Output type: relay output.
Response time: 12ms.
All points of independence.
38 point terminal station.
With the surge absorber.
CE certification.
The number of I/O thyristor DC motor control required tube DC motor speed control system is the main form of DC speed regulation,
The thyristor rectifier unit is used to supply power to the DC motor.
PLC control of the DC drive system, the input of the PLC in addition to the main signal outside the signal,
We need to consider the switching signal, the fault signal transmission device, brake signal and fan fault signal.
The output of the PLC mainly consider the speed command signal positive 1~3 level, 1~3 level, allowing reverse switching signal and brake open signal etc..
In general, a reversible DC drive system controlled by PLC is approximately 12 input points and 8 output points,
An irreversible DC drive system requires 9 inputs and 6 output points.
MITSUBISHI PLC is the main product in the production of MITSUBISHI motor in Dalian.
It uses a kind of programmable memory for its internal storage procedures,
Execute logic operation, sequence control, timing, counting and arithmetic operations, user oriented instruction,
And through digital or analog input / output control of various types of machinery or production process.
Control solenoid valve required I/O points by the action principle of the solenoid valve can be knoown,
A single coil solenoid valve with PLC control to 2 input and 1 output,
A double coil solenoid valve requires 3 inputs and 2 outputs,
A button needs an input; a light sensitive switch needs 4 or 2 inputs,
A signal lamp needs 1 output, band switch,
Several bands are required for several inputs,
In general, a variety of position switches are required to take up 2 input points AJ35TJ-8D Manual AJ35TJ-8D Manual .
Related products
MITSUBISHI
DC input module
AJ35TB2-8D
MITSUBISHI DC input module AJ35TB2-8D
DC input points: 8 points. Input voltage and
MITSUBISHI
Transistor output module
AJ35TJ-8T1
MITSUBISHI Transistor output module
 AJ35TJ-8T1
Output points: 8 points. Output voltage and c
MITSUBISHI
DC input / relay output module
AJ35TB1-16DR
MITSUBISHI DC input / relay output module AJ35TB1-16DR
DC input points: 8 points. Input voltage and