Cable length: 10m.
For the connection between QCPU and GOT.
For connection between two GOT.
Applicable models: GT16, GT15, GT11, GT27, GT25. For video input (NTSC/PAL) 4ch.
Applicable model: GT27. Protective film for 4.5 inch screen.
Scrub, 5.
Applicable model: GT1030. Accessories for 8.4 inch models GT1020-LBLW Manual .
Applicable models: GT16, GT15. A series of high performance models that are widely used in network or single machine work environments
GT1020-LBLW
Screen size: 10.4 inches.
Display color: 256 color or more color.
Mounting type: panel mounting type.
Resolution: SVGA (800 x 600).
Display device: TFT color (high brightness, wide viewing angle).
Host frame color: black.
Power type: DC24V.
Communication interface: with built-in RS-422 GT1020-LBLW Manual .
Ideal model for high performance in a network or independent operation environment.
User storage capacity: 9MB (GT15__-VNB_:5MB).
Device USB port.
Standard RS-232 interface.
Support video /RGB unit.
If the capacitive touch screen is in the middle of the operation, the display resolution or display mode of the touch screen is changed again,
Or the refresh rate of the touch screen controller is adjusted by itself, and the cursor and the touch point can not be felt when the cursor is not corresponding to the touch point,
Must be re calibrated to the touch screen system GT1020-LBLW Manual .
In order to ensure the normal operation of the touch screen system, in addition to ensure the proper installation of the system software,
Must also remember that in a host do not install two or more than two kinds of touch screen driver,
This will cause the system to run in conflict, so that the touch screen system can not be used properly MITSUBISHI touch screen Manual MITSUBISHI touch screen Manual . Cable length: 1.5m.
For the connection between FXCPU and GOT.
Connection between a power supply and an operating switch and a GOT.
Applicable model: HandyGOT MITSUBISHI touch screen Manual . Protective film for 10.4 inch screen.
Scrub (frame: white), 5.
Applicable model: GT15. 5.7 inches.
Surface treatment: anti reflective film.
Protective film color: No.
USB protection cover parts: there is an opening.
Set number: 5.
Applicable model: GT27. Oil resistant cap for 15 inch screen.
Applicable model: GT16. Features: high cost of second models.
Picture size: 10.4 inches.
Resolution: VGA.
Display: TFT color.
Panel color: black.
Power type: AC100~240V.
Specification rich, design at ease
GT23 standard supports SD memory card and standard equipped with Ethernet, RS-232, RS-422/485, host/device USB interface.
Support log, one to many connections, FA transparent transmission and other diverse FA machine related functions.
System configuration diagram shows in order to form the connection with the GOT programmable controller system,
Easily confirm module status. In addition, after touching each module,
Can start its corresponding expansion function, to facilitate system maintenance, shorten the time of failure.
1, simple design
In order to cope with the use of a variety of scenarios, to abandon all the nonsense of the decoration, the use of straight tone of the minimalist design.
2, plane body
Surface mining pure plane design, easy to clean. (USB interface at the back)
3, Ethernet interface
Up to 2 different manufacturers can be connected to the FA machine.
4, RS-232 interface
Can connect all kinds of FA machine, bar code reader, serial printer.
5, RS-422/485 interface
Can be connected to a variety of FA machines, bar code reader.
6, USB interface: device USB (Mini-B USB)
Can connect to the computer to transfer data.
7, USB interface: host USB (USB-A)
USB data can be transmitted through the USB memory or read log data, such as the GOT data, but also can be connected tto the use of the mouse, keyboard GT1020-LBLW Gateway Functions Manual.
8, SD memory card slot
Can save alarm and log data, such as a large number of data.
Can be collected through the GOT programmable controller, temperature regulator and other data, and to chart, list display GT1020-LBLW Manual .
Computer analysis can also be used to save the data. Even in the case of a power outage, the log data can be saved to the built-in SRAM.