MITSUBISHI Q00JCPU-SET Manual Q00JCPU-SET Special Instructions Programming Manual

2 channel.
Differential input: 40kpps/400kpps/800kpps/2Mpps/4Mpps/8Mpps.
Count input signal: EIA standard RS-422-A (differential line driver).
DC input: 10kpps/100kpps/200kpps.
Count input signal: DC5/12/24V 7 ~ 10mA.
External output: DC24V.
Consistent output: Transistor (drain), DC12/24V, 0.1A/ point, 0 Q00JCPU-SET Programming Manual. 8A/ common.
40 pin connector.
Multifunctional counting / timing module (QD65PD2)
Very precise positioning and tracking Q00JCPU-SET
Maximum count rate of up to 8Mpps (differential input 4 phase 2 frequency multiplication), is 2 times in the past.
Multifunctional and convenient use!
Pulse measuring function... Measurement resolution of 100ns, can be performed with high precision pulse measurement.
PWM output function Q00JCPU-SET Programming Manual. .. Configuration of the maximum 200 PWM kHz output function. Available 0.1 s single
Bit change duty cycle, to achieve ultra precise output control.
Cam switching function... The output of the 8 points, 16 step / output cam switch.
High precision timing control can be realized by cam switch.
Complete complex control using a consistent test!
Uniform output function... Can provide support for complex applications Q00JCPU-SET Programming Manual.
According to the specific circumstances, choose to use the cam switch function or the same output function.SRAM memory card.
RAM capacity: 128KB. Output points: 16 points.
Output voltage and current: DC12~24V; 0.5A/ point; 4A/ common.
OFF leakage current: 0.1mA.
Response time: 1ms.
16 points and 1 common ends.
Source type.
18 point spring clip connection terminal.
With the surge absorber.
With fuse.
Ultra high speed processing, production time is shortened, better performance.
As applications become larger and more complex, it is necessary to shorten the system operation cycle time.
The operation period can be shortened by the super high basic operation speed 1.9ns.
In addition to achieve in the past with the control of single-chip high-speed control,
The system performance can be improved by reducing the total scan time,
To prevent any possible performance bias.
Convenient processing of large capacity data.
In the past can not achieve the standard RAM and SRAM card file register area of continuous access,
The boundary of each area should be considered in programming.
The SRAM 8MB extension card is installed in the high speed universal QCPU,
Standard RAM can be used as a continuous file register,
Capacity up to 4736K words, thus simplifying the programming.
Thus, even if the memory space of the soft element is insufficient,
Can also be installed by the expansion of SRAM card, easy to extend the file register area.
The address register is extended to 32 bits, which can be programmed to go beyond the traditional 32K word,
And to achieve the extension to the file register to all regions of the file register.
In addition, the processing speed of the index modification plays an important role in the efficient operation of structured data (array),
The speed has been improved.
When the index is used to modify the program repeatedly (e.g. from FOR to NEXT), the scan time can be reduced.
With the help of sample tracking function, the starting time is shortened
By using the sampling and tracking function, it is convenient to analyze the data when the fault occurs,
Testing procedures for the time, etc., can shorten the time of failure analysis and start-up time.
In addition, the multi CPU system also helps to determine the dataa transceiver time between the CPU module Q00JCPU-SET Manual.
Can be used to analyze the data collected by programming tools,
In the form of charts and trend charts, the data changes of the bit soft element and the word soft element can be easily diisplayed Q00JCPU-SET Manual.
And the sampling tracking results can be stored in LogViewer GX form CSV,
By recording data display and analysis tool LogViewer GX to display.