pressure sensor E8F2-A01C INSTRUCTION sheet OMRON E8F2-A01C Manual

The main body: terminal type, temperature input type.
Category: control output 1 point type (power supply AC100 ~ 240V).
Shell color: black.
Control output: relay output and long life.
Control mode: standard or heating cooling.
Auxiliary output points: 2 points.
Heater with broken wire, SSR fault, heater over current detection function /ES1B power supply: single phase heater with detection function E8F2-A01C INSTRUCTION sheet E8F2-A01C
Event entry point: 2.
Transfer output: -.
Communication: -.
48mm general thermostat has been upgraded & function / performance upgrade.
Indicates that the accuracy is increased and the preventive maintenance function is increased,
Further performance improvement.
E5CN-U (insert type) add analog input and current output type E8F2-A01C INSTRUCTION sheet.
Add PV/SV status display function, convenient to check the state of the thermostat (automatic / manual, RUN/STOP, alarm),
Interactive display PV/SV.
Increase the number of control output ON/OFF counting function, can prevent the maintenance of temperature controller internal relay. High performance price ratio standard type proximity sensor.
Standard cable protector E8F2-A01C INSTRUCTION sheet.
The new DC two-wire type.
Non polar proximity sensor.
Type: DC three wire / wire type.
Shape: non shield, M8.
Detection range: 2mm.
Output configuration: PNP.
Action mode: NC. Sensing method: Reflective model(for mark detection) OMRON E8F2-A01C Manual.
Connection method: Pre-wired (2 m).
Sensing distance: 30±5 mm.
Extremely thin beam ideal for detection of minute objects and marks OMRON E8F2-A01C Manual.
Ideal for detection of small objects and slight color differences.
Bad mark detection.
Detection of thin wire of 200 μ.
Detection of slight level differences. Power: AC.
Purpose: general purpose type.
Amplifier unitAppearance: Unshielded.
Sensing surface: Front.
Sensing distance: 2 OMRON E8F2-A01C Manual. 5 mm.
Output configuration: NPN.
Model: Operation mode, NC.
Advanced Performance and Wide.
Range of Selections in a Super.
compact Size.
Only 5.5 × 5.5 mm with a built-in Amplifier.
Maximum sensing distance: 2.5 mm. Stable detection even with,
workpiece fluctuations.
Response frequency: 1 kHz.
Low current consumption. Size: 96 x 96mm.
Control output 1: relay output.
Control output 2:--.
Auxiliary output: 2 independent points.
Power supply voltage: AC100 ~ 240V.
Terminal shape: screw terminal table type.
Input category: full range multi input.
Heating wire break, SSR fault detection function: -.
Communication: -.
Event input: 4 points.
Remote SP input: -.
Transfer output: -.
Large screen display white PV legible. From selection to setting and operation are simple and easy to use.
Full capacity, function and performance of I/O. Suitable for more applications.
E5AC white LCDPV display height is about 25mm.
The upper panel and the front panel are equipped with tool ports.
With the communication conversion line (sold separately) connected to the computer to establish the controller without the need to install the wire for power supply.
Easy to install CX-Thermo (sold separately).
50ms high speed sampling period.
Model can be equipped with up to 4 point auxiliary output, 6 point event input,
1 point transfer output and remote SP input, suitable for a wide range of applications E8F2-A01C .
The main body is short, the thickness is only 60mm.
Easy to use programmable logic controller (PLC) is connected to the programmable logic controller (PLC).
The temperrature controller is connected to each other by using the component communication E8F2-A01C INSTRUCTION sheet.
A new type of proportional control allows you to control the valve.