FX2N-4AD PDF datasheet MITSUBISHI FX2N-4AD datasheet PDF catalog

Axis of control: 2.
Interpolation: there are.
Program memory: built-in 7.8k step RAM.
Applicable PLC:FX1N, FX2N, FX3U, FX2NC (to FX2NC-CNV-IF).
Applicable PLC:FX3UC (to FX2NC-CNV-IF or FX3UC-1PS-5V).
Can control 2 axes for linear interpolation, arc interpolation.
Can not be connected to the PLC, while running alone MITSUBISHI FX2N-4AD PDF catalog.
1 can control 1 axes,
FX1N, FX2N, PLC FX3U up to 8 units can be connected,
PLC FX2NC up to 4 units can be connected,
FX3UC PLC can connect up to 7 units, and a plurality of shafts can be independently controlled FX2N-4AD
Can output up to 200kHz of the pulse train.
The connection function of the absolute position detection function and the manual pulse generator.
Can be used in the form of flow chart programming software, visual programming MITSUBISHI FX2N-4AD PDF catalog. Function extension board for RS-422 communication.
No DC24V consumption, do not take up input and output. Power: 0.4kw.
Purpose: high frequency braking resistor.
The use rate of the built-in regenerative brake of the transducer can be promoted.
When using the FR-ABR type brake resistor, the short circuit piece between the terminal PR-PX is removed MITSUBISHI FX2N-4AD PDF catalog. Does not remove the short circuit chip will lead to overheating of the brake resistor.
The utilization rate of the regenerative braking should be less than the allowable brake use rate in the above table.
With the operating frequency of the brake resistor to reach 300 degrees C or higher, it is necessary to take protective measures and cooling.
MYS type resistor can be used. But please pay attention to the allowable brake use rate.
Do not remove the terminal P/+ and P1 between the short circuit chip, in addition to connecting the DC reactor.
The installation of thermal relay, to avoid overheating and burn the braking resistor. Power: 30kw.
Voltage: 200V.
The power factor of the input power factor is up to 0.99 and above (100% load).
Can be connected to multiple inverters, to achieve a common DC bus mode.
Equipped with standard power retrogradation function. Input and output points: 40 points.
Power supply: AC100-240V.
Input points: 24 points.
Output points: 16 points.
Output form: relay output.
Power consumption: 37W.
Weight: 0.7KG.
Outline dimension: 130x90x86mm.
EEPROM memory cartridge with program transfer function.
Third generation standard model.
Easy to use integrated models and flexible scalability.
Condensed convenience of using the usual FX3 series.
Its high price by the most suitable for small scale control.
High speed operation.
Basic instructions: 0.21 s/ instruction.
Application instruction: 0.5 s/ instruction.
Large capacity memory.
Built in program memory 32000 steps.
Auxiliary relay: 7680 points.
Timer: 320 points.
Counter: 235.
Data register: 8000.
Extended register: 24000 point.
Extended file register: 24000.
A free combination of PLC.
FX3G basic unit: 14/24/40/60 point.
FX3GA is a compact PLCC, simple design and with the basic functions of the FX3 series FX2N-4AD PDF datasheet.
Through the strengthening of the built-in function and flexible expansion, expanded in various fields of application.
Third generation standard model.
High flexiibility FX2N-4AD PDF datasheet.
Suitable for small scale control of high cost.
Control points to 128 points, the use of CC-Link remote I/O can control the maximum 256 points.