OMRON E5CN-HTQQ2FD Basic Type

Sensing method: Diffuse-reflective.
Appearance: Vertical.
Connection method: Pre-wired Connector (M12).
Sensing distance: 700mm.
Water- and Oil-resistant.
Photoelectric Sensor with.
Metal Housing Used for Long.
range Sensing.
Excellent resistance against the water and oil.
Easy application in locations with oil mist E5CN-HTQQ2FD .
Long-range sensing up to 30 m with Through-beam models.
Shock resistance rated at 1,000m/s2 E5CN-HTQQ2FD
Product lineup includes metal M12 pre-wired connector models.
NPN/PNP selector switch output. Appearance: Shielded, M18.
Sensing distance: 5 mm.
Output: PNP.
Model: Operation mode NO.
Aluminum and Iron Both.
Detectable from Long Distances. Continuation of the E6B2 high cost, value also have more choice E5CN-HTQQ2FD .
E6B3, E6C4 blockbuster debut! Complementary output of the first starting high anti interference.
40mm diameter, shaft diameter of phi 8mm universal, with strong axial load capacity.
50mm diameter, shaft diameter of phi 10mm rugged, with strong axial load capacity,
At the same time, the use of IP65 anti drip, anti oil structure.
E6B2 complementary output will be issued over the same period E5CN-HTQQ2FD .
Connection length to reach a full 30m!
Resolution (pulse / rotation):10~3600P/R.
Power supply voltage: DC12 ~ 24V
Consumption current: 100mA below.
Output state: complementary output.
Maximum response frequency: 100kHz.
Output phase difference: A phase, B phase difference 90 plus or minus 45.
Starting torque: M / 10mN below (at room temperature).
Maximum allowable speed: 6000r/min.
Axial force: radial...... 80N, axial...... 50N. Small amplifier built-in type photoelectric switch
The body is thin and long, saving space, the volume is only 50 * 50 * 17.4mm
M.S.R function can detect smooth, shiny objects
New photoelectric -IC, enhance anti interference
Power reverse connect, output short circuit and output reverse protection (AC model no)Size: 48 x 96mm.
Type: power AC/DC24V with.
Shell color: black.
Control output 1: output unit mode.
Control output 2: output unit mode.
Control mode: standard or heating cooling.
Auxiliary output points: 2 points.
The detection function of the broken wire and SSR fault of heater: detection function of single phase or three phase heater.
Event entry point: 2.
Transfer output: -.
Remote SP:4 to 20mA input.
Communication: RS-232C.
General thermostat new high performance (high resolution, high speed, high precision input) type products.
Support simple operation, preventive maintenance.
A new type of liquid crystal, which can communicate with the front through the infrared port, is adopted,
Visual angle, contrast can be improved.
High resolution 5 bit display / can display 0.01 degrees C.
High speed sampling period 60ms.
All models complete a variety of (to the thermocouple /Pt/ analog input switching), 1 machines to support a variety of sensors.
Also supports remote SP.
Add PV/SV status display function, convenient to check the staate of the thermostat (automatic / manual, RUN/STOP, alarm),
Interactive display PV/SV E5CN-HTQQ2FD Basic Type".
By supporting software (Ver.4.0 CX-Thermo) to carry out a simple function (AND/OR logic and delay),
Be able to execute flexible contact output E5CN-HTQQ2FD Basic Type".
Increase the control output ON/OFF number counting function, can predict the temperature controller internal relay fault.
Position ratio type.