SGDV-7R6A15A002FT003 Manual Yaskawa AC Servo Drives SGDV-7R6A15A002FT003 MECHATROLINK-II Commands USER'S MANUAL

Large capacity SGMVV type servo motor.
Rated output: 37KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit absolute value type.
Rated speed: 1500r/min.
The main mechanical structure: flange type, straight shaft (with keyway and screw).
Optional parts: do not buy pieces.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties Yaskawa AC Servo Drives USER'S MANUAL SGDV-7R6A15A002FT003
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r/min and 1500r/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen Yaskawa AC Servo Drives USER'S MANUAL.








High performance, use the best type of servo unit (purpose type).
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: three phase AC200V.
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Design sequence: B.
Hardware specification: base mounting type (standard).
Function: pressure feedback control function Yaskawa AC Servo Drives USER'S MANUAL.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models.
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time SGDV-7R6A15A002FT003 USER'S MANUAL.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device SGDV-7R6A15A002FT003 USER'S MANUAL.
FT005 (support for rotary table purposes): with the rotation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table.
FT006 (fixed point through the output function): no need to pass through the upper device can be set through the output (Chu Fa) SGDV-7R6A15A002FT003 USER'S MANUAL.
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller. Sigma -V series servo motor SGMGV.
Rated output: 4.4kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal.
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F. SGDV-7R6A15A002FT003 Manual.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) Yaskawa AC Servo Drives USER'S MANUAL.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation