SGMGV-1EADA2C Manual Yaskawa SGMGV-1EADA2C Setup Rotational Motor Product Manual

No speed reducer in inertia, large torque servo motor type SGM7G (rated speed 1500r\/min).
Rated output: 0.85kw.
Power supply voltage: AC200V.
Serial encoder: 24 bit absolute value type.
Design sequence: A.
Shaft end: straight shaft with keyway, with screw.
Optional parts: with oil seal.
Yaskawa servo motor, also known as YASKAWA Yaskawa servo motor,
Origin of Japan, in Shenyang, China, Jiading, Shanghai also has a factory,
Is to make the position of the object, the position, the state and other output controlled,
Automatic control system capable of following an arbitrary change of an input target value (or a given value) Yaskawa SGMGV-1EADA2C Product Manual SGMGV-1EADA2C
It is divided into AC servo motor and DC servo motor,
In the domestic semiconductor, liquid crystal manufacturing devices, electronic components packaging equipment, machine tools and general machinery has been widely used in Yaskawa SGMGV-1EADA2C Product Manual.
As a leading enterprise for the first time Yaskawa servo drive, put forward the concept of "mechatronics",
Now has become a universal termLarge capacity SGMVV type servo motor.
Rated output: 37KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit absolute value type Yaskawa SGMGV-1EADA2C Product Manual.
Rated speed: 800r\/min.
The main mechanical structure: support mounting type, straight shaft (without keyway and screw).
Optional parts: do not buy pieces.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenCapacity type of direct drive servo motor SGMCS.
Rated torque: M \/ 150N.
Servo motor outside diameter size: 290mm.
Serial encoder: 20 bit absolute value type (absolute value of 1 circles) (standard).
Design sequence: the size of the outer diameter of the service motor is marked as E model.
Flange specifications: face C, reverse load side (lead).
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Capacity rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange typee SGMGV-1EADA2C Manual.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80%% (not dew) SGMGV-1EADA2C Manual.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation