Yaskawa SGM7P-04AFAHC2C Manual SGM7P-04AFAHC2C HARDWARE MANUAL

Sigma -V series servo motor SGMAV.
Rated output: 0.15kw (150W).
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: with two side plane seat (optional).
Optional: no matching.
Super power rate.
Small capacity.
Ultra low inertia
Instantaneous maximum torque (rating 300%) SGM7P-04AFAHC2C HARDWARE MANUAL.
Equipped with a high resolution serial encoder (20 bit) SGM7P-04AFAHC2C
Max speed up to 6000r\/min.
Variety is complete (50W ~ 1.0kw, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above SGM7P-04AFAHC2C HARDWARE MANUAL.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection SGM7P-04AFAHC2C HARDWARE MANUAL.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationServo motor SGMDH type.
Rated speed: 3000r\/min.
Power: 2.2kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal, D90V brake.
Partial flat series: the need to install the servo motor in a small space.
Rich motor series.
Equipped with brake, belt reducer, such as a wealth of motor products.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain.
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regenerative resistance connection terminals.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistorSigma -V series servo motor SGMSV.
Rated output: 4.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal, with the brake (DC90V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resisstance grade: F SGM7P-04AFAHC2C Manual.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGM7P-04AFAHC2C Manual.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation