YASKAWA SGMVV-2BA3B6F Door Switches SGMVV-2BA3B6F

Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 7.5kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Matching (hardware): shelf installation type + paint.
Realize real time communication YASKAWA SGMVV-2BA3B6F.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control SGMVV-2BA3B6F Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time YASKAWA SGMVV-2BA3B6F.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control YASKAWA SGMVV-2BA3B6F.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly . Servo motor SGMDH type.
Rated speed: 3000r\/min.
Power: 4.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal, D90V brake.
Partial flat series: the need to install the servo motor in a small space.
Rich motor series.
Equipped with brake, belt reducer, such as a wealth of motor products.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain.
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regenerative resistance connection terminals.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistorSGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 4.0N.
Servo motor outside diameter size: 290mm.
Serial encoder: 20 bit absolute value type (absolute value of 1 circles) (standard).
Design sequence: the size of the outer diameter of the service motor is marked as E model.
Flange specification: face C, reverse load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installationn method: flange ttype SGMVV-2BA3B6F.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80%% ((not dew) SGMVV-2BA3B6F.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
SGMVV-2BA3B6F Operation manual/Instructions/Model selection sample download link: /searchDownload.html?Search=SGMVV-2BA3B6F&select=5