LK Automation Limited
Home >> Price >> MITSUBISHI >> MR-J4-DU55KB4 MITSUBISHI MR-J4-DU55KB4
Brand sort

MR-J4-DU55KB4 MITSUBISHI MR-J4-DU55KB4

Country: JAPAN
Name: Servo driver
Price: 0
MITSUBISHI MR-J4-DU55KB4
Cable length: 25 meters.
For QCPU and GOT (need A9GT-QCNB) connection.
For the connection between GOT and GOT. Cable length: 5.0m.
For the connection between the two graphic operations.
Applicable models: GT16, GT15, GT11. MITSUBISHI inverter series: FR-F840.
Voltage level: three phase 400V.
Power: 11kw MITSUBISHI MR-J4-DU55KB4.
SLD converter rated current: 25.0A.
Structure and function: Standard model.
Type: CA.
Substrate coating: have MR-J4-DU55KB4
2 times the power consumption of the wind turbine and pump and the speed of the 3 power consumption is proportional to the speed of the rotating speed.
Through the speed control of the frequency converter to adjust the air flow, can reduce the power consumption MITSUBISHI MR-J4-DU55KB4.
Give full play to the performance of the motor .
The excitation current is always adjusted to the best state, which can improve the efficiency of the motor.
Load torque is smaller, can further improve energy efficiency.
For example, when a general motor is used, the optimal excitation control mode in the 4% motor load torque is about 30% more than that of the V/F control MITSUBISHI MR-J4-DU55KB4. Drive: MR-H_ACN series built-in positioning function .
Rated output: 3.5KW.
In servo drive speed closed loop,
Rotor speed measurement accuracy is very important to improve the dynamic and static characteristics of the speed control loop.
In order to seek the balance between measurement precision and system cost, incremental photoelectric encoder is generally used as the speed measuring sensor,
The corresponding method is M/T velocity measurement.
Although the M/T measurement method has a certain measurement accuracy and a wide range of measurement,
But this method has its inherent defects,
Mainly includes: the measurement period must be detected at least one complete encoder pulse, limiting the minimum detectable speed.
2 control system for speed control of the timer switch is difficult to maintain synchronization,
Can not guarantee the accuracy of measurement in the situation where the speed change is larger.
Therefore, it is difficult to improve the speed tracking and control performance of servo drive by using the traditional speed loop design method. Input points: 16 points.
Voltage: DC12/24V.
Current: 4/10mA.
Response time: 6ms/1ms (high speed mode).
8 points / a common end.
Negative utility.
20 point terminal station.
Each scanning process. Focus on the input signal sampling. Focus on the output signal to refresh.
Input refresh process. When the input port is closed,
Program in the implementation phase, the input end of a new state, the new state can not be read.
Only when the program is scanned, the new state is read.
A scan cycle is divided into the input sample, the program execution, the output refresh.
The contents of the component image register are changed with the change of the execution of the program.
The length of the scan cycle is determined by the three.
CPU the speed of executing instructions.
Time of instruction.
Instruction count.
Due to the adoption of centralized sampling.
Centralized output mode.
There exist input / output hysteresis phenomena, i.e., the input / output response delay.
PLC selection with the development of PLC technology, more and more types of PLC products,
Function is becoming more and more perfect, and its application is more and more extensive.
Different series of different models of PLC has different performance, applicable occasions also have different emphasis,
Price also has a greater difference. Therefore PLC selection,
Under the premise of meeeting the control requirements,
Should consider the best performance to price ratio, a reasonable choice of PLC MR-J4-DU55KB4.
System program memory for storing system program,
Including management procedures, monitoring procedures, as well as the user program tto do the compiler to compile the process of interpretation MR-J4-DU55KB4.
Read only memory. Manufacturers use, content can not be changed, power does not disappear.
MR-J4-DU55KB4 Operation manual/Instructions/Model selection sample download link: /searchDownload.html?Search=MR-J4-DU55KB4&select=5


...more relevant model market price >>>>
Related products
MITSUBISHI
Servo driver
MR-J4-15KB-RJ010
MITSUBISHI Servo driver MR-J4-15KB-RJ010
1 axis servo amplifier. MITSUBISHI gener
MITSUBISHI
Servo driver
MR-J4-100B-RJ010
MITSUBISHI Servo driver MR-J4-100B-RJ010
1 axis servo amplifier. MITSUBISHI gener
MITSUBISHI
Servo driver
MR-J4-200B4
MITSUBISHI Servo driver MR-J4-200B4
1 axis servo amplifier. MITSUBISHI gener
MITSUBISHI
Servo driver
MR-J4-DU45KB4
MITSUBISHI Servo driver MR-J4-DU45KB4
Drive unit. MITSUBISHI universal AC serv