Sale MR-J4-20B-RJ010 MITSUBISHI MR-J4-20B-RJ010

Cable length: 20m.
For MR-J2S-700A (4) /CP/CL or less.
Encoder for HC-SFS; HC-LFS; HC-RFS; 2000r/min HA-LFS; HC-UFS servo motor.
-L represents bending life.
MITSUBISHI general purpose AC servo amplifier MELSERVO-J2-Super series.
Rated output: 22.0kw.
SSCNET interface.
Voltage: 3 phase AC400V.
Complete synchronization system with SSCNET high speed serial communication,
The communication cycle between the controller and the servo amplifier is the longest 0 MR-J4-20B-RJ010 888ms.
Such systems will be able to provide high reliability and high performance.
When connecting the servo system with SSCNET,
In the motion system, the parameters of the servo amplifier and the acquisition of the data will be displayed on the motion controller MR-J4-20B-RJ010.
Connect a dedicated cable with an amplifier and a controller to form a SSCNET system.
This simple connection method reduces the routing time and helps to prevent noise.
Even in the MELSERVO-J2-SUPER series products using high resolution coding standards, the command frequency is no limit MR-J4-20B-RJ010.
It is only necessary to add a battery on the servo amplifier, which can form the absolute value system .
Currently there are more than 1000000 high reliability SSCNET servo amplifier networks in use.Multi axis integrated servo amplifier.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series.
Axis number: 2 axis.
Rated output A axis (Note 1): 0.4kw.
Rated output B axis (Note 1): 0.4kw.
Interface: SSCNET III /H.
Note the 1:A axis, B axis, C axis indicates the name of a type of multi axis servo amplifier axis. The C axis represents the 3 axis one type servo amplifier.
Support SSCNET III /H. 1 unit can drive 2 servo motor two axis servo amplifier.
More energy saving, space saving, less wiring, low cost.
Inherited the high performance and high reliability.
Will, as always, adhere to and uphold the excellent quality of MELSERVO.
MR-J4 has inherited the excellent design of existing products.
Its essence to its dregs, create advantage and cost effective utilization rate,
Make full use of renewable resources, to create a new product. Input points: 32 points.
Voltage: DC12/24V.
Current: 2.5/5mA.
Response time: 0.2ms.
8 points / a common end.
Positive / negative sharing.
38 point terminal station.
Each scanning process. Focus on the input signal sampling. Focus on the output signal to refresh.
Input refresh process. When the input port is closed,
Program in the implementation phase, the input end of a new state, the new state can not be read.
Only when the program is scanned, the new state is read.
A scan cycle is divided into the input sample, the program execution, the output refresh.
The contents of the component image register are changed with the change of the execution of the program.
The length of the scan cycle is determined by the three.
CPU the speed of executing instructions.
Time of instruction.
Instruction count.
Due to the adoption of centralized sampling.
Centralized output mode.
There exist input / output hysteresis phenomena, i.e., the input / output response delay.
PLC selection with the development of PLC technology, more and more types of PLC products,
Function is becoming more and more perfect, and its application is more and more extensive.
Different series of different models of PLC has different performance, applicable occasions also have different emphasis,
Price also has a greater difference. Therefore PLC selection,
Under the premise of meeeting the control requirements,,
Should consider the best performance to price ratio, a reasonable choice of PLC MITSUBISHI MR-J4-20B-RJ010.
System program memory for storing system program,
Including management procedures, monitoring procedures, as well as the user program tto do the compiler to compile the process of interpretation MITSUBISHI MR-J4-20B-RJ010.
Read only memory. Manufacturers use, content can not be changed, power does not disappear.
MR-J4-20B-RJ010 Operation manual/Instructions/Model selection sample download link: /searchDownload.html?Search=MR-J4-20B-RJ010&select=5