MITSUBISHI FR-A7AR FR-A7AR

Input type: DC input, positive public end / negative public end.
Input points: 4 points.
Input response time: 0.5ms below /1.5ms.
Rated input voltage / current: DC24V/4mA.
External connection: 2 wire.
Spring clip terminal.
Do not need to re tighten, suitable for wire specifications for 0.3~1.5MM square MITSUBISHI FR-A7AR.
Terminal block is 2 piece structure.
An input module shared by the common terminal of the positive and negative FR-A7AR
The 8 point of the output module is appended to the source type.
Can be installed along the 6 direction. Control axis: maximum 8 axes.
Greater flexibility.
PLC control and motion control using independent CPU, optimize the system configuration MITSUBISHI FR-A7AR.
More than 4 CPU modules can be freely selected in multi CPU system .
MITSUBISHI SSCNET control function.
By using the high speed serial communication mode, we can easily construct the synchronization system of the servo motor.
The motion controller and the servo amplifier can be quickly connected by a connector, and the connection is simplified.
Each 1 CPU can control up to 32 axes at the same time MITSUBISHI FR-A7AR.
Can control the small capacity from 10W to 55KW large capacity servo motor .
Through the use of digital oscilloscope function, can be used to control the power distance, speed, position and other motor information monitoring.Drive unit.
MITSUBISHI universal AC servo amplifier MELSERVO-J4 series.
Rated output: 37kw.
Interface: SSCNET III /H.
Power supply: three phase AC200V.
Support position control, speed control, torque control.
Position control to follow the position instructions.
When the control is inserted, the position control is performed.
Speed control follows the speed command to control the speed within a certain range.
Torque control to follow the torque command to control the stable torque.
Function of switching amplitude. The increase in the process of switching and stopping,
And in the operation of the use of the switching signal, switching growth. AC input points: 32 points.
Input voltage and current: 120V ~ 10mA AC100.
Response time: 35ms.
16 point /1 a public side.
36 point terminal station.
Number of stations: 4 stops.
Compact remote I/O unit.
Equipment layer / field bus CC-Link device layer is the PLC and other control devices and sensors and drive devices connected to the field network,
Network for the lowest layer of the whole network system.
Using CC-Link field bus connection, the number of wiring is greatly reduced,
Improve the maintainability of the system.
And, not just the amount of data ON/OFF and other switches,
Can also be connected to the ID system, bar code reader, inverter, man-machine interface and other intelligent devices,
From the completion of a variety of data communication, the management of the terminal production information can be realized,
On the centralized management of the state of the machine movement,
Make maintenance work efficiency also greatly improved.
Q series PLC in the use of CC-Link function better,
And easier to use.
Mitsubishi Co PLC network inherited the traditional use of the MELSEC network,
And make it better in terms of performance, function, easy to use etc..
Provides a layer of three layers of clear network, to provide the most suitable network products for a variety of uses.
The information layer /Ethernet (Ethernet) information layer is the highest level of the network system,
Mainly in the PLC, the device controller and production management with PC transmission between production management information, quality management information and the operation of equipment, etc.,
Information layer using the most common Ethernet.
It is not only able to connect the PC system UNIX, windows system, etc.,
And can connect a variety of FA deevices .
Thee Ethernet module has the function of Internet e-mail receiving and sending,
The user can send and receive the production information conveniently in any place of the world,
Build a remote monitoring management system FR-A7AR.
At the same time, tthee use of the Internet FTP server functions and MELSEC protocol can be very easy to achieve the program upload / download and transfer of information FR-A7AR.
FR-A7AR Operation manual/Instructions/Model selection sample download link: /searchDownload.html?Search=FR-A7AR&select=5