LK Automation Limited
Home >> Products >> MITSUBISHI >> Touch Screen >> Touch screen accessories >> GOT-A900 touch screen accessories >> AC30R4-25P MITSUBISHI The PC card interface unit MITSUBISHI AC30R4-25P

AC30R4-25P MITSUBISHI The PC card interface unit MITSUBISHI AC30R4-25P

Brand: MITSUBISHI
Name: RS-422 cable
Model: AC30R4-25P
Cable length: 3 meters.
For QnA/A/FX (FX1, FX2, FX2C) CPU and GOT connection between.
For connection between FA-CNV_CBL and GOT.
For connection between FX-2PIF and GOT.
For connection between FX-422AW0 and GOT.
For serial communication module AJ71QC24 (N) -R4 and GOT connection between.
For connection between AJ65BT-G4-S3 and GOT.

For QCPU (Q) / transport controller CPU (Q Series) the bus (2 channel) thin type unit.
Applicable models: GT15, GT16, GT27, GT25. A series of high performance models that are widely used in network or single machine work environments.
Screen size: 10.4 inches.
Display color: 16 color.
Mounting type: panel mounting type MITSUBISHI AC30R4-25P.
Resolution: VGA (640 x 480).
Display device: TFT color.
Host frame color: black AC30R4-25P
Power type: DC24V.
Communication interface: with built-in RS-422.
Ideal model for high performance in a network or independent operation environment.
User storage capacity: 9MB (GT15__-VNB_:5MB).
Device USB port.
Standard RS-232 interface.
Support video /RGB unit.
If the capacitive touch screen is in the middle of the operation, the display resolution or display mode of the touch screen is changed again,
Or the refresh rate of the touch screen controller is adjusted by itself, and the cursor and the touch point can not be felt when the cursor is not corresponding to the touch point,
Must be re calibrated to the touch screen system MITSUBISHI AC30R4-25P.
In order to ensure the normal operation of the touch screen system, in addition to ensure the proper installation of the system software,
Must also remember that in a host do not install two or more than two kinds of touch screen driver,
This will cause the system to run in conflict, so that the touch screen system can not be used properly MITSUBISHI AC30R4-25P MITSUBISHI The PC card interface unit. Protective film for 15 inch screen.
Transparent (frame: white), 5.
Applicable model: GT16. Series: multimedia and advanced features and features of a variety of high-performance models MITSUBISHI The PC card interface unit.
Screen size: 15 inches.
Display color: 256 color or more color.
Installation type: compatible with multimedia and video /RGB.
Resolution: SVGA (800 x 600).
Display device: TFT color (high brightness, wide viewing angle) MITSUBISHI The PC card interface unit.
Host frame color: black.
Power type: DC24V.
Communication interface: with built-in RS-422.
High performance models with multimedia and advanced features and functionality (including embedded communications capabilities).
User storage capacity: 15MB (GT16__-VNB__:11MB).
With HOST USB and device USB port.
Standard Ethernet, RS-422/485 and RS-232 ports.
Support multimedia and video /RGB units.
Analog touch panel.
Do not let the touch screen surface with water drops or other soft things stick to the surface,
Otherwise, the touch screen is easy to mistake that there is a hand touch caused by surface acoustic wave screen is not allowed.
In addition to cleaning the dirt on the surface of the touch screen,
You can use a soft dry cloth or a cleaning agent to clean out the center of the screen carefully,
Or use a dry soft cloth dipped in industrial alcohol or glass cleaning fluid to clean the touch screen surface.
Touch screen response is slow if you use a hand or other touch to touch the surface acoustic wave touch screen,
This shows that it is likely that the touch screen system has been obsolete, the internal clock frequency is too low,
Or because there is water in the surface of the touch screen to make the touch screen mobile, rapid response recovery,
To replace or upgrade the system must, or use ddry cloth touch screen on the surface of the water AC30R4-25P.
If the user is operating the touch screen, the direction of the touch move is to the left,
But the cursor of the system moves to the right,
The failure may be due to the conneection of the control box and the touch screen connected to the connector or the touch screen,
Users as long as the direction of the re exchange of it MITSUBISHI AC30R4-25P.


...More relevant models >>>>