Home
>> Products
>> MITSUBISHI
>> FX series PLC
>> FX all modules and accessories
>> FX3U module
>> FX3U-2HC MITSUBISHI FX3U-2HC High speed counting module
FX3U-2HC MITSUBISHI FX3U-2HC High speed counting module
Brand:
MITSUBISHI
Name: High speed counting module
Model: FX3U-2HC
Maximum frequency: 200kHz.
Input points: 2 points.
Output form: transistor 4 point output.
Weight: 0.2kg.
1 FX3U-2HC can enter the 2CH high speed signal, can achieve the maximum count of 200kHz.
Through the comparison of the value of the PLC set, each ch with 2 points of high-speed output terminal.
In the 2 phase count, can be set 1, 2, 4 frequency.
Can be achieved by PLC or external input to count the licensing / prohibition.
Can also be connected to the linear drive output type of the encoder.
FX3UC host connected to the FX2NC-CNV-IF, the need for FX3U-2HC or FX3UC-IPS-5V.
...More relevant models >>>>
Name: High speed counting module
Model: FX3U-2HC
Maximum frequency: 200kHz.
Input points: 2 points.
Output form: transistor 4 point output.
Weight: 0.2kg.
1 FX3U-2HC can enter the 2CH high speed signal, can achieve the maximum count of 200kHz.
Through the comparison of the value of the PLC set, each ch with 2 points of high-speed output terminal.
In the 2 phase count, can be set 1, 2, 4 frequency.
Can be achieved by PLC or external input to count the licensing / prohibition.
Can also be connected to the linear drive output type of the encoder.
FX3UC host connected to the FX2NC-CNV-IF, the need for FX3U-2HC or FX3UC-IPS-5V.
Output points: 32 points
Output form: Transistor (drain type).
Connection status: connector.
In order to extend the input output of the device.
Also has a built-in power supply products.
The maximum number of points for the input and output is 256.
Expansion module: up to 16 units (in addition to the power expansion module)
The total number of CC-Link, AnyWireASLINK, and Bitty series of remote I/O is 512 points MITSUBISHI FX3U-2HC FX3U-2HC Analog input expansion board (2 channel).
Can be installed in FX1N, PLC FX1S, providing 2 channel analog input of the board.
Because it is embedded in the PLC installation, so do not need to install space.
Can be mixed with the use of voltage input and current input. Display: 16 characters x 4 lines MITSUBISHI FX3U-2HC.
Can monitor, change the value of software components.
Can also be simple to operate, change the value.
Equipped with a button operation can be used (operator certification function) and control through the PLC control function,
Can be used with the function expansion board.
Can be installed directly to the FX3GA, FX3G, FX3GE, no wiring. Input and output points: 24 points.
Power supply: DC24V MITSUBISHI FX3U-2HC.
Input points: 14 points.
Output points: 10 points.
Output form: transistor output (source).
Power consumption: 21W.
Weight: 0.55KG.
Outline dimension: 90x90x86mm.
A free combination of PLC.
FX3G basic unit: 14/24/40/60 point.
FX3GA is a compact PLC, simple design and with the basic functions of the FX3 series MITSUBISHI High speed counting module.
Through the strengthening of the built-in function and flexible expansion, expanded in various fields of application MITSUBISHI High speed counting module.
Third generation standard model.
High flexibility.
Suitable for small scale control of high cost.
Control points to 128 points, the use of CC-Link remote I/O can control the maximum 256 points.
High speed operation.
Basic instructions: 0.21 s/ instruction MITSUBISHI High speed counting module.
Application instruction: 0.5 s/ instruction.
Large cappacity memory FX3U-2HC.
Built in program memory 32000 steps.
EEPROM memory cartridge with program transfer function.
Third generation standard model.
Easy to use integrated models and flexible scalability.
Condensed convenience of using tthe usual FX3 series MITSUBISHI FX3U-2HC.
Its high price by the most suitable for small scale control. Length: 3m.
Specification: D-sub 25 pin (male), D-sub 25 pin (male).
Output form: Transistor (drain type).
Connection status: connector.
In order to extend the input output of the device.
Also has a built-in power supply products.
The maximum number of points for the input and output is 256.
Expansion module: up to 16 units (in addition to the power expansion module)
The total number of CC-Link, AnyWireASLINK, and Bitty series of remote I/O is 512 points MITSUBISHI FX3U-2HC FX3U-2HC Analog input expansion board (2 channel).
Can be installed in FX1N, PLC FX1S, providing 2 channel analog input of the board.
Because it is embedded in the PLC installation, so do not need to install space.
Can be mixed with the use of voltage input and current input. Display: 16 characters x 4 lines MITSUBISHI FX3U-2HC.
Can monitor, change the value of software components.
Can also be simple to operate, change the value.
Equipped with a button operation can be used (operator certification function) and control through the PLC control function,
Can be used with the function expansion board.
Can be installed directly to the FX3GA, FX3G, FX3GE, no wiring. Input and output points: 24 points.
Power supply: DC24V MITSUBISHI FX3U-2HC.
Input points: 14 points.
Output points: 10 points.
Output form: transistor output (source).
Power consumption: 21W.
Weight: 0.55KG.
Outline dimension: 90x90x86mm.
A free combination of PLC.
FX3G basic unit: 14/24/40/60 point.
FX3GA is a compact PLC, simple design and with the basic functions of the FX3 series MITSUBISHI High speed counting module.
Through the strengthening of the built-in function and flexible expansion, expanded in various fields of application MITSUBISHI High speed counting module.
Third generation standard model.
High flexibility.
Suitable for small scale control of high cost.
Control points to 128 points, the use of CC-Link remote I/O can control the maximum 256 points.
High speed operation.
Basic instructions: 0.21 s/ instruction MITSUBISHI High speed counting module.
Application instruction: 0.5 s/ instruction.
Large cappacity memory FX3U-2HC.
Built in program memory 32000 steps.
EEPROM memory cartridge with program transfer function.
Third generation standard model.
Easy to use integrated models and flexible scalability.
Condensed convenience of using tthe usual FX3 series MITSUBISHI FX3U-2HC.
Its high price by the most suitable for small scale control. Length: 3m.
Specification: D-sub 25 pin (male), D-sub 25 pin (male).
...More relevant models >>>>
Last one: MITSUBISHI Input module for temperature sensor FX3U-4LC
next one: MITSUBISHI 1 axis positioning control module FX3U-1PG
Related download