Home
>> Products
>> MITSUBISHI
>> Servo driver/Servo motor
>> MR-C series
>> MR-C40A MITSUBISHI Servo motor without oil seal MR-C40A
MR-C40A MITSUBISHI Servo motor without oil seal MR-C40A
Brand:
MITSUBISHI
Name: Servo driver
Model: MR-C40A
Type: MR-C type.
Symbol 10A for motor models: HC-PQ43.
Power supply voltage: single phase AC220V.
Drive: servo drive in the development of the premise of the frequency conversion technology,
Current loop in the drive,
Speed loop and position loop (frequency converter without the ring) have carried out a more precise control than the general frequency control technology and algorithm,
In function is also a lot stronger than the traditional servo,
The main point can be precise position control.
The control speed and position are controlled by the pulse sequence transmitted by the upper controller,
The internal algorithm of the driver and the faster and more accurate calculation and better performance of electronic devices to make it more superior to the inverter.
...More relevant models >>>>
Name: Servo driver
Model: MR-C40A
Type: MR-C type.
Symbol 10A for motor models: HC-PQ43.
Power supply voltage: single phase AC220V.
Drive: servo drive in the development of the premise of the frequency conversion technology,
Current loop in the drive,
Speed loop and position loop (frequency converter without the ring) have carried out a more precise control than the general frequency control technology and algorithm,
In function is also a lot stronger than the traditional servo,
The main point can be precise position control.
The control speed and position are controlled by the pulse sequence transmitted by the upper controller,
The internal algorithm of the driver and the faster and more accurate calculation and better performance of electronic devices to make it more superior to the inverter.
Motor series: low inertia, small capacity.
Using a serial absolute / incremental encoder.
Rated output power: 0.6kw.
Rated speed: 3000rpm.
With a brake band.
Shaft end: straight shaft.
AC servo motor and brushless DC servo motor in the function of the difference: AC servo is better, because it is a sine wave control, torque ripple small MITSUBISHI MR-C40A.
DC servo is a trapezoidal wave. DC servo is simple and cheap MR-C40A Servo motor series: low inertia, small capacity.
Rated output: 0.1kw.
Rated speed: 3000r/min.
Electromagnetic brake: No.
Oil seal: have.
Corresponding servo amplifier: MR-JE-10B/MR-JE-10A.
Support position control, speed control, torque control, push and press control.
Position control can use linear, arc interpolation controller, fixed size feed control, target position change and other rich functions MITSUBISHI MR-C40A.
The position control and torque control are realized by switching control mode.
The gain adjustment of servo can be simply performed by the advanced one key tuning function.
At the same time, it is also able to suppress the low frequency vibration of the manipulator by the advanced vibration suppression control II,
Shorten the time to complete the positioning, so as to achieve the production of the rhythm of the shortening MITSUBISHI MR-C40A. Servo motor series: low inertia, medium and large capacity.
Rated output: 15.0kw.
Rated speed; 1000r/min.
Electromagnetic brake: No.
Power supply: 400V MITSUBISHI Servo motor without oil seal.
Most suitable for medium and large capacity, low inertia type products in high frequency operation or acceleration and deceleration operation MITSUBISHI Servo motor without oil seal.
Improve the environmental performance of HG-SR, HG-JR series of products using IP67.
High speed & high torque. Shorten the positioning time, achieve high-speed equipment.
100 scene, there are 100 different drive control.
In order to meet the needs of the diverse and detailed field,
MR-J4 product line configuration, providing a wealth of servo amplifier and servo motor products MITSUBISHI Servo motor without oil seal.
Can meet the different needs of different customers. Drive: MR-H_ACN series CC-LINK features.
Rated output: 22KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
Annd the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive MR-C40A.
Usually, such testing system is only used to test the rotational speeed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive MITSUBISHI MR-C40A.
Using a serial absolute / incremental encoder.
Rated output power: 0.6kw.
Rated speed: 3000rpm.
With a brake band.
Shaft end: straight shaft.
AC servo motor and brushless DC servo motor in the function of the difference: AC servo is better, because it is a sine wave control, torque ripple small MITSUBISHI MR-C40A.
DC servo is a trapezoidal wave. DC servo is simple and cheap MR-C40A Servo motor series: low inertia, small capacity.
Rated output: 0.1kw.
Rated speed: 3000r/min.
Electromagnetic brake: No.
Oil seal: have.
Corresponding servo amplifier: MR-JE-10B/MR-JE-10A.
Support position control, speed control, torque control, push and press control.
Position control can use linear, arc interpolation controller, fixed size feed control, target position change and other rich functions MITSUBISHI MR-C40A.
The position control and torque control are realized by switching control mode.
The gain adjustment of servo can be simply performed by the advanced one key tuning function.
At the same time, it is also able to suppress the low frequency vibration of the manipulator by the advanced vibration suppression control II,
Shorten the time to complete the positioning, so as to achieve the production of the rhythm of the shortening MITSUBISHI MR-C40A. Servo motor series: low inertia, medium and large capacity.
Rated output: 15.0kw.
Rated speed; 1000r/min.
Electromagnetic brake: No.
Power supply: 400V MITSUBISHI Servo motor without oil seal.
Most suitable for medium and large capacity, low inertia type products in high frequency operation or acceleration and deceleration operation MITSUBISHI Servo motor without oil seal.
Improve the environmental performance of HG-SR, HG-JR series of products using IP67.
High speed & high torque. Shorten the positioning time, achieve high-speed equipment.
100 scene, there are 100 different drive control.
In order to meet the needs of the diverse and detailed field,
MR-J4 product line configuration, providing a wealth of servo amplifier and servo motor products MITSUBISHI Servo motor without oil seal.
Can meet the different needs of different customers. Drive: MR-H_ACN series CC-LINK features.
Rated output: 22KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
Annd the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive MR-C40A.
Usually, such testing system is only used to test the rotational speeed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive MITSUBISHI MR-C40A.
...More relevant models >>>>
Last one: 
next one: Related download