Home
>> Products
>> MITSUBISHI
>> Servo driver/Servo motor
>> MR-J4 series
>> MR-J4 servo amplifier
>> MR-J4-DU30KB4 MITSUBISHI Servo driver MR-J4-DU30KB4
MR-J4-DU30KB4 MITSUBISHI Servo driver MR-J4-DU30KB4
Brand:
MITSUBISHI
Name: Servo driver
Model: MR-J4-DU30KB4
Drive unit.
MITSUBISHI universal AC servo amplifier MELSERVO-J4 series.
Rated output: 30kw.
Interface: SSCNET III /H.
Power supply: three phase AC400V.
Support position control, speed control, torque control.
Position control to follow the position instructions.
When the control is inserted, the position control is performed.
Speed control follows the speed command to control the speed within a certain range.
Torque control to follow the torque command to control the stable torque.
Function of switching amplitude. The increase in the process of switching and stopping,
And in the operation of the use of the switching signal, switching growth.
...More relevant models >>>>
Name: Servo driver
Model: MR-J4-DU30KB4
Drive unit.
MITSUBISHI universal AC servo amplifier MELSERVO-J4 series.
Rated output: 30kw.
Interface: SSCNET III /H.
Power supply: three phase AC400V.
Support position control, speed control, torque control.
Position control to follow the position instructions.
When the control is inserted, the position control is performed.
Speed control follows the speed command to control the speed within a certain range.
Torque control to follow the torque command to control the stable torque.
Function of switching amplitude. The increase in the process of switching and stopping,
And in the operation of the use of the switching signal, switching growth.
MITSUBISHI general purpose AC servo amplifier MR-J2 series.
Rated output: 0.4kw.
Interface: SSCNET type.
Voltage: single phase AC200V.
MR-J2 series server system has the ability to carry out a higher precision control,
Using high performance CPU, greatly improve the responsiveness of the product,
Speed loop frequency response increased to 550HZ MITSUBISHI MR-J4-DU30KB4.
Various series of servo motors are suitable for different control requirements,
The encoder on the servo motor supports ABS mode,
As long as the servo amplifier on the other plus batteries,
Can form an absolute position system MR-J4-DU30KB4 Servo motor series: low inertia, medium / high power.
Rated output: 1.5kw.
Rated speed: 3000r/min.
Electromagnetic brake: with MITSUBISHI MR-J4-DU30KB4.
Shaft end specification: Standard (straight axis).
Features: low inertia for high speed / acceleration and deceleration operation occasions.
IP level: IP67.
Application example:
1, food processing machinery.
2, printing machine.
3, injection molding machine (11KW, 15KW).
4, large press machine (11KW, 15KW).
The protection level of the HF-SP/HF-JP series servo motor is IP67 (except the shaft part) MITSUBISHI MR-J4-DU30KB4.
Low inertia of the power servo motor (0.5kW ~ 9kW), the maximum speed: 6000r/min (rated speed: 3000r/min),
Suitable for high frequency positioning and acceleration / deceleration operations, especially for food processing machines and printing machines MITSUBISHI Servo driver.
Low inertia, high power, no cooling fan servo motor (11kW and 15kW), maximum speed: 3000r/min (rated speed: 1500r/min) MITSUBISHI Servo driver.
The motor structure is more compact due to the adoption of the non cooling fan design, and the connection is reduced by using the power source connector.
(compared with the HF-LP series servo motor with the same power, the volume is reduced by about 46%, and the weight is reduced by about 34%,
Suitable for high frequency positioning and acceleration / deceleration operations, especially for injection molding machines and large presses MITSUBISHI Servo driver.
HF-JP703 (4) /903 (4) maximum speed: 5000r/min. Length: 0.5 meters.
Purpose: MR-JE-A, MR-TB50 connection with. MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 2.0kw.
Interface type: CC-Link communication type (built-in positioning function).
Power specification: three phase AC400V.
Positioning operation by setting position and rotational speed data in the positioning table and receiving the start signal from the main controller.
The setting of the position and speed of the positioning table, as well as the start and stop operation can be completed through CC-Link communication.
By using the MR-J3-D01 extension IO unit, the DI/O instruction can be used to select and locate the table.
(CC-Link can not be used for MR-J3-D01 communications).
With built-in positioning function of the servo amplifier, can be set through the CC-Link communications and speed data. (corresponding to the CC-Link version: Ver.1.10)
Can be achieved through the CC-Link communications to start, stop and monitoring and other operaations MR-J4-DU30KB4.
Serial communication reduce wiring.
Distributed servo control system can be built by CC-Link communication.
The parameters of unit MR-PRU03 (optional) the parameter setting, operation and monitoring more convenient.
The servo amplifier can be used for speed control operation MITSUBISHI MR-J4-DU30KB4.
When the two stations are occupied, the speed can be set directly by the remote register.
Rated output: 0.4kw.
Interface: SSCNET type.
Voltage: single phase AC200V.
MR-J2 series server system has the ability to carry out a higher precision control,
Using high performance CPU, greatly improve the responsiveness of the product,
Speed loop frequency response increased to 550HZ MITSUBISHI MR-J4-DU30KB4.
Various series of servo motors are suitable for different control requirements,
The encoder on the servo motor supports ABS mode,
As long as the servo amplifier on the other plus batteries,
Can form an absolute position system MR-J4-DU30KB4 Servo motor series: low inertia, medium / high power.
Rated output: 1.5kw.
Rated speed: 3000r/min.
Electromagnetic brake: with MITSUBISHI MR-J4-DU30KB4.
Shaft end specification: Standard (straight axis).
Features: low inertia for high speed / acceleration and deceleration operation occasions.
IP level: IP67.
Application example:
1, food processing machinery.
2, printing machine.
3, injection molding machine (11KW, 15KW).
4, large press machine (11KW, 15KW).
The protection level of the HF-SP/HF-JP series servo motor is IP67 (except the shaft part) MITSUBISHI MR-J4-DU30KB4.
Low inertia of the power servo motor (0.5kW ~ 9kW), the maximum speed: 6000r/min (rated speed: 3000r/min),
Suitable for high frequency positioning and acceleration / deceleration operations, especially for food processing machines and printing machines MITSUBISHI Servo driver.
Low inertia, high power, no cooling fan servo motor (11kW and 15kW), maximum speed: 3000r/min (rated speed: 1500r/min) MITSUBISHI Servo driver.
The motor structure is more compact due to the adoption of the non cooling fan design, and the connection is reduced by using the power source connector.
(compared with the HF-LP series servo motor with the same power, the volume is reduced by about 46%, and the weight is reduced by about 34%,
Suitable for high frequency positioning and acceleration / deceleration operations, especially for injection molding machines and large presses MITSUBISHI Servo driver.
HF-JP703 (4) /903 (4) maximum speed: 5000r/min. Length: 0.5 meters.
Purpose: MR-JE-A, MR-TB50 connection with. MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 2.0kw.
Interface type: CC-Link communication type (built-in positioning function).
Power specification: three phase AC400V.
Positioning operation by setting position and rotational speed data in the positioning table and receiving the start signal from the main controller.
The setting of the position and speed of the positioning table, as well as the start and stop operation can be completed through CC-Link communication.
By using the MR-J3-D01 extension IO unit, the DI/O instruction can be used to select and locate the table.
(CC-Link can not be used for MR-J3-D01 communications).
With built-in positioning function of the servo amplifier, can be set through the CC-Link communications and speed data. (corresponding to the CC-Link version: Ver.1.10)
Can be achieved through the CC-Link communications to start, stop and monitoring and other operaations MR-J4-DU30KB4.
Serial communication reduce wiring.
Distributed servo control system can be built by CC-Link communication.
The parameters of unit MR-PRU03 (optional) the parameter setting, operation and monitoring more convenient.
The servo amplifier can be used for speed control operation MITSUBISHI MR-J4-DU30KB4.
When the two stations are occupied, the speed can be set directly by the remote register.
...More relevant models >>>>
Last one: MITSUBISHI Servo driver MR-J4-DU30KB-RJ
next one: MITSUBISHI Servo driver MR-J4-DU30KB4-RJ
Related download