Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> SGMCS type direct drive motor
>> SGMCS-25EDB11 YASKAWA SGMCS-25EDB11 Rated torque: M \/ 25N Direct drive servo motor
SGMCS-25EDB11 YASKAWA SGMCS-25EDB11 Rated torque: M \/ 25N Direct drive servo motor
Brand:
Yaskawa
Name: Direct drive servo motor
Model: SGMCS-25EDB11
SGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 25N.
Servo motor outside diameter size: 290mm.
Serial encoder: 20 bit Delta (optional).
Design sequence: the size of the outer diameter of the service motor is marked as E model.
Flange specification: face C, reverse load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
Name: Direct drive servo motor
Model: SGMCS-25EDB11
SGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 25N.
Servo motor outside diameter size: 290mm.
Serial encoder: 20 bit Delta (optional).
Design sequence: the size of the outer diameter of the service motor is marked as E model.
Flange specification: face C, reverse load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Type: SGDH type drive.
Capacity: 30W.
Voltage: single phase 110V.
Mode: torque, speed, position.
Test platform for mutual feedback of servo driver and motor.
Test platform with adjustable analog load.
A test platform with an actuator that has no load is used.
Test platform for driving the inherent load by using motor YASKAWA SGMCS-25EDB11.
Test platform using on line test method.
This test system is composed of three parts,
Were measured servo driver - motor system, the system inherent load and host computer SGMCS-25EDB11
The host computer sends the speed command signal to the servo driver, and the servo system starts to run according to the instruction.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data YASKAWA SGMCS-25EDB11. Servo motor type SGMPH (speed: 3000r/min).
Power: 0.4kw.
Power supply voltage: single phase AC200V.
Serial encoder: 16 bit absolute value.
Design sequence: A.
Shaft end: straight shaft with key.
Optional parts: with oil seal, DC90V brake.
Partial flat series: the need to install the servo motor in a small space YASKAWA SGMCS-25EDB11.
Flexible user system.
For you to build the best system to enrich the product line to support you.
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer YASKAWA Direct drive servo motor.
And then, because of its compliance with international standards, in the world can be assured that the use of YASKAWA Direct drive servo motor.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operated.Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 1.5kw YASKAWA Direct drive servo motor.
Power supply voltage: three phase AC400V.
Design sequence: A type.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needs 1,
Pullse generator for D/A converter or position instruction without speed / torque command SGMCS-25EDB11.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control YASKAWA SGMCS-25EDB11.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
Capacity: 30W.
Voltage: single phase 110V.
Mode: torque, speed, position.
Test platform for mutual feedback of servo driver and motor.
Test platform with adjustable analog load.
A test platform with an actuator that has no load is used.
Test platform for driving the inherent load by using motor YASKAWA SGMCS-25EDB11.
Test platform using on line test method.
This test system is composed of three parts,
Were measured servo driver - motor system, the system inherent load and host computer SGMCS-25EDB11
The host computer sends the speed command signal to the servo driver, and the servo system starts to run according to the instruction.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data YASKAWA SGMCS-25EDB11. Servo motor type SGMPH (speed: 3000r/min).
Power: 0.4kw.
Power supply voltage: single phase AC200V.
Serial encoder: 16 bit absolute value.
Design sequence: A.
Shaft end: straight shaft with key.
Optional parts: with oil seal, DC90V brake.
Partial flat series: the need to install the servo motor in a small space YASKAWA SGMCS-25EDB11.
Flexible user system.
For you to build the best system to enrich the product line to support you.
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer YASKAWA Direct drive servo motor.
And then, because of its compliance with international standards, in the world can be assured that the use of YASKAWA Direct drive servo motor.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operated.Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 1.5kw YASKAWA Direct drive servo motor.
Power supply voltage: three phase AC400V.
Design sequence: A type.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needs 1,
Pullse generator for D/A converter or position instruction without speed / torque command SGMCS-25EDB11.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control YASKAWA SGMCS-25EDB11.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
...More relevant models >>>>
Last one: Yaskawa Direct drive servo motor SGMCS-17EDB11
next one: Yaskawa Direct drive servo motor SGMCS-35EDB11
Related download