LK Automation Limited
Home >> Products >> Yaskawa >> Servo driver / motor >> SGDM series >> SGMGH type servo motor >> SGMGH-09A2D2E YASKAWA Motor for high precision machine tool SGMGH-09A2D2E

SGMGH-09A2D2E YASKAWA Motor for high precision machine tool SGMGH-09A2D2E

Brand: Yaskawa
Name: Motor for high precision machine tool
Model: SGMGH-09A2D2E
Servo motor SGMGH type.
Rated speed: 1000r/min.
Power: 0.9kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: high precision machine tool.
Shaft end: straight shaft without key.
Optional parts: with oil seal, DC24V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control.













Sigma -V series servo motor SGMSV.
Rated output: 2.0kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with hold brake (DC24V).
Super power rate.
Variety is complete (1 YASKAWA SGMGH-09A2D2E. 0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit) SGMGH-09A2D2E
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type YASKAWA SGMGH-09A2D2E.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationLarge capacity SGMVV type servo motor YASKAWA SGMGH-09A2D2E.
Rated output: 45KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit absolute value type.
Rated speed: 1500r\/min.
The main mechanical structure: flange type, straight shaft (with keyway and screw).
Optional parts: keep the brake (DC24V), with dust YASKAWA Motor for high precision machine tool.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties YASKAWA Motor for high precision machine tool.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenServo motor SGMGH type YASKAWA Motor for high precision machine tool.
Rated speed: 1500r\/min.
Power: 7.5Kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with DC90V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,,
Alarm can only turn off the main circuit power supply, easy to maintain SGMGH-09A2D2E.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 YASKAWA SGMGH-09A2D2E.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control


...More relevant models >>>>
Related download