Sigma -V series servo motor SGMSV.
Rated output: 2.5kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal.
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Servo motor SGMSH type.
Rated speed: 3000r\/min.
Power: 2.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: straight shaft without key.
Optional parts: with DC90V brake.
Ultra high power response series: the need for small inertia, high torque YASKAWA SGMSV-25ADA6S.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain
SGMSV-25ADA6S
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regenerative resistance connection terminals YASKAWA SGMSV-25ADA6S.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistorServo motor type SGMPH (speed: 3000r\/min).
Power: 0.2kw.
Power supply voltage: single phase AC100V.
Serial encoder: 16 bit relative value.
Design sequence: Waterproof standard IP67.
Shaft end: straight shaft without key.
Optional parts: with DC24V brake.
Partial flat series: the need to install the servo motor in a small space YASKAWA SGMSV-25ADA6S.
Flexible user system.
For you to build the best system to enrich the product line to support you.
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer YASKAWA servo motor.
And then, because of its compliance with international standards, in the world can be assured that the use of YASKAWA servo motor.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operatedSigma -v series servo unit SGDV.
Maximum applicable motor capacity: 3kw.
Power supply voltage: three phase AC200V YASKAWA servo motor.
Design sequence: B type.
Interface: analog voltage, pulse sequence type (linear servo motor).
Matching (hardware): base mounting type (standard).
With the latest technology to pursue the use of convenience.
The use of new non adjustment function, no need to adjust.
The vibration suppression function is also strengthened, and the load fluctuation can be effectively suppressed.
Greatly shorten the setting time.
Using engineering tool SigmaWin+ too set the guide function and the distribution confirmation function,
Can look at the picture simply to complete the start SGMSV-25ADA6S.
Achieve a high response 1kHz above.
Equipped with a new advanced automatic tuning function.
Through the model tracking control, the positioning time is shortened,
And through the vibration suppression function, easy to achieve a smooth mechanical control YASKAWA SGMSV-25ADA6S.