FX2NC-96MT-DSS MITSUBISHI FX2NC-96MT-DSS

Protective film for 10.4 inch screen.
Scrub, 5.
Applicable model: GT15. Cable flat cable;
Connector with 20 pin installed at both ends of the fuse.
Length 1.5M. MR-J2M multi axis servo amplifier drive unit.
Rated output: 0.4kw.
The accuracy, stability, response characteristics and operating frequency of the main indicators of the servo control system are four aspects,
Especially in the frequency band width and precision FX2NC-96MT-DSS
Frequency bandwidth of the system, the system frequency response characteristics of the system to reflect the servo system to track the fast. Needle number: 20.
Specification: Cable flat cable connector, supporting 10 sets MITSUBISHI FX2NC-96MT-DSS. Oil resistant cap for 10.4 inch screen.
Applicable model: GT16 . 1 axis servo amplifier.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series.
Rated output: 2.0kw.
Interface: SSCNET III /H.
Power supply: three phase AC400V.
0.6kW and 1kW above the servo amplifier.
Servo amplifier supporting SSCNET III /H.
Complete synchronization system capable of using high speed serial optical communication MITSUBISHI FX2NC-96MT-DSS.
Can be combined with the servo system controller to maximize the performance of the servo system .
2 low frequency vibration can be suppressed at the same time by supporting the seismic algorithm of 3 inertial equipment.
Configurator2 MR to achieve convenient adjustment.
Effectively restrain the low frequency aftershock effect produced by the front end of the boom or the main body of the device 100Hz.
Can effectively shorten the time to control the stability of the aftershock.
In the XY design of trajectory control, improve the accuracy of arc track.
At the same time, it can effectively control the phenomenon of quadrant protrusion caused by the rotation direction of the servo motor, which is caused by friction and twisting. Used to reduce radio noise.The input and output module installation number: 12.
DIN guide rail mounting adapter type: R6DIN1.
Size (H) * (32.5mm) * (W) * (D): * 439mm * 101mm. "Input points: 16 points.
Input voltage and current: 8mA AC100-120V (AC100V; 60Hz) /7mA (AC100V; 50Hz).
Response time: 20ms.
16 points / a common end.
18 point terminal station.
A variety of modules with excellent performance,
Meet the needs of various control from analog to location.
Q series module products include a variety of types of I/O, analog and positioning function module.
Can fully meet the switch, sensor, such as the input and output, temperature, weight, flow and motor, drive control,
As well as the requirements of high-precision control of the positioning of the industry, the control needs of various fields.
Can also be used in combination with the CPU module to achieve appropriate control.
Continue to go beyond, to climb the peak of Q series.
Strengthen security function.
Can be set up to 32 characters of the file password.
In addition to the English letters, numbers, but also the use of special characters,
To further enhance the security of the password.
In addition, only pre registered devices are allowed to access CPU,
To intercept unauthorized access to unauthorized users.
Therefore, it is important to prevent the outflow of important program assets and protect intellectual property rights.
Easy connection programming tool via ethernet.
Programmming tools (Works22 GX, Developer GX) and CPU direct connection (1 to 1),
No need to carry out the IP address settings FX2NC-96MT-DSS. And there is no need to select the cable, the straight line and the cross line can be used.
Therefore, this connection method annd the use of USB, can easily communicate with the CPU,
Even the operators are not familiar with the network settings can easily establish a connection FX2NC-96MT-DSS.
FX2NC-96MT-DSS Operation manual/Instructions/Model selection sample download link: /searchDownload.html?Search=FX2NC-96MT-DSS&select=5