MITSUBISHI FX3G-60MT/ES-A Price FX3G-60MT/ES-A

Drive unit 200VAC/400VAC level.
MITSUBISHI motor general AC servo amplifier MELSERVO-J3 series.
Need conversion unit MR-J3-CR55K) supporting the use of.
Rated output: 30kw.
Interface type: general pulse interface type.
Power specification: three phase AC200V.
Pulse train and analog input as universal interface FX3G-60MT/ES-A Price.
Can choose the position, speed and torque control mode.
The use of advanced tuning features such as advanced vibration suppression control and adaptive filter,
Greatly improve the performance of the machine FX3G-60MT/ES-A
MR-J3, your partner.
Higher performance, more features, more convenient to use.
Highest performance in the industry FX3G-60MT/ES-A Price.
Speed response frequency up to 2.1kHz. Enter points: 64 points .
Rated input voltage: DC24V.
Common way: 32 point / public end.
Input / output occupied points: 64 points (I/O distribution: 64 points).
External wiring connection: 40 pin connector two.
The input and output module is also called control module, which can output signal when there is control requirement,
Or provide a switch signal to the controlled device,
At the same time, the feedback signal of the equipment can be received to report to the host computer,
Is an important part of the fire alarm linkage system,
The input and output modules in the market can provide a pair of passive normally open / normally closed contacts,
For controlling the controlled equipment, the module of the part can be set by the parameters,
Set to active output, corresponding to the two input and output modules, multiple input and output modules, and so on FX3G-60MT/ES-A Price. Output points: 64 points.
Output voltage and current: DC12~24V; 0.1A/ point; 2A/ common.
OFF leakage current: 0.1mA.
Response time: 1ms.
32 points and 1 common ends.
Source type.
40 pin connector.
With heat protection.
With the surge absorber.
With fuse.
With the help of sample tracking function, the starting time is shortened
By using the sampling and tracking function, it is convenient to analyze the data when the fault occurs,
Testing procedures for the time, etc., can shorten the time of failure analysis and start-up time.
In addition, the multi CPU system also helps to determine the data transceiver time between the CPU module.
Can be used to analyze the data collected by programming tools,
In the form of charts and trend charts, the data changes of the bit soft element and the word soft element can be easily displayed.
And the sampling tracking results can be stored in LogViewer GX form CSV,
By recording data display and analysis tool LogViewer GX to display.
Ultra high speed processing, production time is shortened, better performance.
As applications become larger and more complex, it is necessary to shorten the system operation cycle time.
The operation period can be shortened by the super high basic operation speed 1.9ns.
In addition to achieve in the past with the control of single-chip high-speed control,
The system performance can be improved by reducing the total scan time,
To prevent any possible performance bias.
Convenient processing of large capacity data.
In the past can not achieve the standard RAM and SRAM card file register area of continuous access,
The boundary of each area should be considered in programming.
The SRAM 8MB extension card is installed in the high speed universal QCPU,
Standard RAM can be used as a continuous file register,
Capacity up to 4736K words, thus simplifying the programming.
Thus, even if the memory space of the soft element is insufficient,
Can also be installed by the expansion of SRAM card, easy to extend the file register area.
The address register is extended to 32 bits, which can be programmed to go beyond the traditional 32K woord,
And to achieve the extension to the file register to all regions of the file register MITSUBISHI FX3G-60MT/ES-A.
In addition, the processing speed of the index modification plays an important role in the efficient operation of structured daataa (array),
The speed has been improved MITSUBISHI FX3G-60MT/ES-A.
When the index is used to modify the program repeatedly (e.g. from FOR to NEXT), the scan time can be reduced.
FX3G-60MT/ES-A Operation manual/Instructions/Model selection sample download link: /searchDownload.html?Search=FX3G-60MT/ES-A&select=5