MR-BKS1CBL10M-A2-H MITSUBISHI MR-BKS1CBL10M-A2-H

Type: MR-J series.
Rated output: 0.4KW.
Suitable for motor series: HA-ME.
Voltage: single phase AC100V.
It is very helpful to improve the stability of the low speed control of the servo motor.
But there is no direct effect to improve the accuracy of position control.
There are, of course, software compensation that is similar to pitch compensation,
Can improve the physical resolution of the single lap, so as to improve the accuracy of positioning control MR-BKS1CBL10M-A2-H
This can be effectively used in the use of the robot control of the indexing table.
It is also because of the application of splicing technology,
The rotary encoder will be more widely used in the high precision servo control in the harsh environment MITSUBISHI MR-BKS1CBL10M-A2-H.
The use of rotary encoder with 224/ in the servo motor has been used in the servo motor.
Encoder serial communication system, the communication frequency can only be limited to 10M. 1 axis servo amplifier.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series.
Rated output: 7.0kw.
Interface: General purpose MITSUBISHI MR-BKS1CBL10M-A2-H.
Power supply: three phase AC400V.
0.6kW and 1kW above the servo amplifier .
Servo amplifier supporting universal interface.
Servo amplifier for universal interface.
Speed / torque control of position control and analog voltage command can be carried out by using pulse train command.
Support Max instruction pulse frequency 4 Mpulses/s.
Improve mechanical properties by high performance motor.
By improving the resolution and processing speed of the encoder,
The rotating servo motor has higher precision and better performance of rotation.
Only open a key type of adjustment function, can be carried out including mechanical resonance filter, high end seismic control II, low pass filter servo gain adjustment.
Easily start advanced seismic function, it can maximize the mechanical properties.
It can automatically adjust the required response settings automatically. Input output cable for A6TBXY36 type connector / terminal row conversion module.
Length 1.5M. 1 channels for analog RGB input.
Applicable model: GT15. For the GT1595-XTB.
Applicable model: GT16. Total input and output points: 40 points.
Input points: 24 points.
Output points: 16 points.
Output type: relay output.
Power supply voltage: AC100-240V.
Input signal voltage: DC24V.
8K capacity of the RAM memory, the maximum can be extended to 16K.
CPU arithmetic processing speed of 0.08 S/ basic instructions.
On the right side of the FX2N series can be connected to the input and output expansion modules and special function modules.
The basic unit is built in the 2 axis independent maximum 20kHz positioning function (transistor output type).
Quick disconnect the terminal block, which adopts excellent maintainability to quickly disconnect the terminal blocks, even if the cable is then replaced by the cable.
Clock function and hour meter function, all of the PLC FX2N has a real-time clock standard.
Continuous scanning function, to define the operation cycle for the application of the continuous scan time.
Input filter adjustment function, you can use the input filter to smooth the input signal (in the basic unit x000 to x017).
Note recording function, Component annotation can be recorded inn the program register MR-BKS1CBL10M-A2-H.
Online program editor, online change the program will not lose the working hours or stop production operation.
RUN/STOP switch, running on panel / stop switch easy to operate.
Remote maintenance, remote programming software caan monitor, upload or uninstall programs and data via modem communications
Password protection, using a eight digit password to protect your program MR-BKS1CBL10M-A2-H.
MR-BKS1CBL10M-A2-H Operation manual/Instructions/Model selection sample download link: /searchDownload.html?Search=MR-BKS1CBL10M-A2-H&select=5