LK Automation Limited
Home >> Products >> OMRON >> Temperature controller >> input device >> ES1-LP10 No need to contact the workpiece, you can measure the temperature OMRON ES1-LP10

ES1-LP10 No need to contact the workpiece, you can measure the temperature OMRON ES1-LP10

Brand: OMRON
Name: Non contact temperature sensor
Model: ES1-LP10
Type: medium temperature.
Measuring temperature range: 0 ~ +500.
The target size: 8mm diameter (from 100mm).
No need to contact the workpiece, you can measure the temperature.
Achieve no damage, health and efficient temperature management.
A small spot diameter 3mm and 8mm diameter two types.
Reproduction of positive and negative 0.5 degrees Celsius, response speed of 0.4 seconds,
(95%) with high precision and high speed measurement.
In addition to the original middle temperature (0 ~ +500 C),
Also added in low temperature (- 50 DEG C ~ +500),
High temperature (0 ~ +1000 degrees C) models.
New measurement distance up to 500mm, 1000mm long distance type.
Use another programmer, can change the temperature monitoring, radiation rate,
Moving average function and output range.
(picture for the installation of programmer in the ES1 body)

Size: 96 x 96mm.
Category: power AC100 ~ 240V with.
Shell color: black.
Control output 1: output unit mode.
Control output 2: output unit mode.
Control mode: standard or heating cooling.
Auxiliary output points: 2 points.
Heater break, SSR fault detection function: single phase or three phase heater detection function OMRON ES1-LP10.
Event entry point: 4.
Transfer output: transfer output (special terminal) ES1-LP10
Remote SP:4 to 20mA input.
Communication: -.
New program type.
A new type of liquid crystal with high performance cost ratio is adopted in the 256 paragraph,
Visual angle, contrast can be improved.
Can be set up to 8 procedures (mode) x 32 (step) procedure.
High resolution 5 bit display / can display 0 OMRON ES1-LP10. 01 degrees C.
High speed sampling period 60ms.
All models complete a variety of (to the thermocouple /Pt/ analog input switching), 1 machines to support a variety of sensors.
Also supports remote SP.
Add PV/SV state display function, to see the state of the thermostat
(automatic / manual, RUN/RESET, alarm), interactive display PV/SV.
Through the support software (Ver.4.3 CX-Thermo) makes the process of setting management becomes very
Simple use of simple computing functions (AND/OR logic and delay) to set the implementation of flexible contact output OMRON ES1-LP10.
Through the infrared port can be carried out from the front of the communication.
The control output ON/OFF times counting function can predict the fault of the internal relay of the temperature controller OMRON Non contact temperature sensor. Ontology: DeviceNet type.
Size: 48 x 96mm OMRON Non contact temperature sensor.
Type: 2 (input).
Control mode: 2 channel standard control /1 channel heating and cooling control /1 channel series control and other functions.
Output (control / transfer) points: 2 points (pulse voltage 1 points + pulse voltage / current and current 2 points each).
Output (SUB) points: 2 points OMRON Non contact temperature sensor.
Event input points: -.
High speed, high precision and multiple input and output universal digital regulator,
Liquid crystal display device with high visibility 5 bit and 3 line.
The high speed sampling period is suitable for the operation of high speed response.
With a backlight liquid crystall display and the 3 display, can display the current value, the target value, the amount of operation ES1-LP10.
1 digital controller can be multi point control / series control / proportion control.
Standard is equipped with a variety of compuuting functions OMRON ES1-LP10.
Equipped with DeviceNet communication function.
Data setting and data monitoring can be performed by means of a communication program.


...More relevant models >>>>