Home
>> Products
>> MITSUBISHI
>> Servo driver/Servo motor
>> MR-J2S series
>> MR-J2S servo driver
>> MR-J2S-60CP-S084 MITSUBISHI MR-J2S-60CP-S084 SSCNET interface servo amplifier
MR-J2S-60CP-S084 MITSUBISHI MR-J2S-60CP-S084 SSCNET interface servo amplifier
Brand:
MITSUBISHI
Name: Built in positioning function servo amplifier
Model: MR-J2S-60CP-S084
"MITSUBISHI general purpose AC servo amplifier MELSERVO-J2-Super series.
Rated output: 0.6kw.
Built in positioning function.
Voltage: 3 phase AC200VAC or single phase AC230V.
Compatible with "MR-J2S- CP-S084" - servo amplifier and interface unit "MR-J2S-TO1" positioning by CC-Link
Simply setting the point table.
AC servo can be used as the driving source of the field network.
Using servo amplifier built-in positioning function, position data and speed data, you can set the CC-Link.
Start, stop and display can also be transmitted through the CC-Link.
Serial communication reduces wiring.
AC servo distributed control system can be easily constructed. "
...More relevant models >>>>
Name: Built in positioning function servo amplifier
Model: MR-J2S-60CP-S084
"MITSUBISHI general purpose AC servo amplifier MELSERVO-J2-Super series.
Rated output: 0.6kw.
Built in positioning function.
Voltage: 3 phase AC200VAC or single phase AC230V.
Compatible with "MR-J2S- CP-S084" - servo amplifier and interface unit "MR-J2S-TO1" positioning by CC-Link
Simply setting the point table.
AC servo can be used as the driving source of the field network.
Using servo amplifier built-in positioning function, position data and speed data, you can set the CC-Link.
Start, stop and display can also be transmitted through the CC-Link.
Serial communication reduces wiring.
AC servo distributed control system can be easily constructed. "
Motor series: low inertia, medium capacity.
Rated output power: 6.0kw.
Rated speed: 1000rpm.
With the brake: without.
Shaft end: straight shaft.
The rotor of the servo motor is a permanent magnet, which is controlled by the U/V/W,
The rotor rotates under the action of the magnetic field, and the encoder feedback signal of the motor is given to the driver,
According to the feedback value and the target value, the driver adjusts the rotation angle of the rotor MITSUBISHI MR-J2S-60CP-S084 MR-J2S-60CP-S084
Accuracy of the servo motor depends on the accuracy of the encoder (number of lines). Type: general purpose AC servo amplifier MR-E series.
Rated output: 0.2kw.
Interface type: analog input interface.
KH003 special mark for Super MR-E MITSUBISHI MR-J2S-60CP-S084.
Servo amplifier terminals are used to reduce the required wiring time.
The connector is located in front of the servo amplifier, which is convenient for cable connection.
The gain adjustment can be easily carried out by the real-time automatic tuning function.
Wide use.
Machining equipment and machine tool feed.
Used for food, packaging equipment and feeding device.
For textile machinery, etc. MITSUBISHI MR-J2S-60CP-S084.
Can improve the performance of equipment. MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 0.6kw.
Interface type: CC-Link communication type (built-in positioning function).
Power specification: three phase AC400V.
Positioning operation by setting position and rotational speed data in the positioning table and receiving the start signal from the main controller MITSUBISHI SSCNET interface servo amplifier MITSUBISHI SSCNET interface servo amplifier.
The setting of the position and speed of the positioning table, as well as the start and stop operation can be completed through CC-Link communication.
By using the MR-J3-D01 extension IO unit, the DI/O instruction can be used to select and locate the table.
(CC-Link can not be used for MR-J3-D01 communications) MITSUBISHI SSCNET interface servo amplifier.
With built-in positioning function of the servo amplifier, can be set through the CC-Link communications and speed data. (corresponding to the CC-Link version: Ver.1.10)
Can be achieved through the CC-Link communications to start, stop and monitoring and other operatioons MR-J2S-60CP-S084.
Serial communication reduce wiring.
Distributed servo control system can be built by CC-Link communication.
The parameters of unit MR-PRU03 (optional) the parameter setting, operation and monitoring more convenient.
The servo amplifier can be used for speed control operation MITSUBISHI MR-J2S-60CP-S084.
When the two stations are occupied, the speed can be set directly by the remote register.
Rated output power: 6.0kw.
Rated speed: 1000rpm.
With the brake: without.
Shaft end: straight shaft.
The rotor of the servo motor is a permanent magnet, which is controlled by the U/V/W,
The rotor rotates under the action of the magnetic field, and the encoder feedback signal of the motor is given to the driver,
According to the feedback value and the target value, the driver adjusts the rotation angle of the rotor MITSUBISHI MR-J2S-60CP-S084 MR-J2S-60CP-S084
Accuracy of the servo motor depends on the accuracy of the encoder (number of lines). Type: general purpose AC servo amplifier MR-E series.
Rated output: 0.2kw.
Interface type: analog input interface.
KH003 special mark for Super MR-E MITSUBISHI MR-J2S-60CP-S084.
Servo amplifier terminals are used to reduce the required wiring time.
The connector is located in front of the servo amplifier, which is convenient for cable connection.
The gain adjustment can be easily carried out by the real-time automatic tuning function.
Wide use.
Machining equipment and machine tool feed.
Used for food, packaging equipment and feeding device.
For textile machinery, etc. MITSUBISHI MR-J2S-60CP-S084.
Can improve the performance of equipment. MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 0.6kw.
Interface type: CC-Link communication type (built-in positioning function).
Power specification: three phase AC400V.
Positioning operation by setting position and rotational speed data in the positioning table and receiving the start signal from the main controller MITSUBISHI SSCNET interface servo amplifier MITSUBISHI SSCNET interface servo amplifier.
The setting of the position and speed of the positioning table, as well as the start and stop operation can be completed through CC-Link communication.
By using the MR-J3-D01 extension IO unit, the DI/O instruction can be used to select and locate the table.
(CC-Link can not be used for MR-J3-D01 communications) MITSUBISHI SSCNET interface servo amplifier.
With built-in positioning function of the servo amplifier, can be set through the CC-Link communications and speed data. (corresponding to the CC-Link version: Ver.1.10)
Can be achieved through the CC-Link communications to start, stop and monitoring and other operatioons MR-J2S-60CP-S084.
Serial communication reduce wiring.
Distributed servo control system can be built by CC-Link communication.
The parameters of unit MR-PRU03 (optional) the parameter setting, operation and monitoring more convenient.
The servo amplifier can be used for speed control operation MITSUBISHI MR-J2S-60CP-S084.
When the two stations are occupied, the speed can be set directly by the remote register.
...More relevant models >>>>
Last one: MITSUBISHI Built in positioning function servo amplifier MR-J2S-60CP
next one: MITSUBISHI Built in program type operational function servo amplifier MR-J2S-60CL
Related download