Home
>> Products
>> MITSUBISHI
>> Servo driver/Servo motor
>> MR-J3 series
>> MR-J3 amplifier
>> MR-J3-DU30KB4 MITSUBISHI MR-J3-DU30KB4 Need conversion unit MR-J3-CR55K) supporting the use of
MR-J3-DU30KB4 MITSUBISHI MR-J3-DU30KB4 Need conversion unit MR-J3-CR55K) supporting the use of
Brand:
MITSUBISHI
Name: SSCNET type III optical fiber communication driver
Model: MR-J3-DU30KB4
Drive unit 200VAC/400VAC level.
MITSUBISHI motor general AC servo amplifier MELSERVO-J3 series.
Need conversion unit MR-J3-CR55K) supporting the use of.
Rated output: 30kw.
Interface type: SSCNET type III fiber communication.
Power specification: three phase AC400V.
High speed serial communication between the SSCNET and the servo amplifier by using the fastest up to 0.44ms communication cycle,
A fully synchronous control system can be constructed.
It is only necessary to insert the special optical fiber into the joint to form SSCNET III network, which greatly reduces the wiring work and reduces the possibility of false wiring.
Due to the adoption of the optical fiber communication, the anti noise ability can be greatly improved and the long distance wiring of 50 meters (maximum 800 meters x 16 axes) can be realized.
A servo amplifier to meet the full closed loop control function MR-J3-B-RJ006.
Suitable for mechanical servo optimization and adjustment!
More advanced optimization adjustment function and control function to maximize mechanical properties.
...More relevant models >>>>
Name: SSCNET type III optical fiber communication driver
Model: MR-J3-DU30KB4
Drive unit 200VAC/400VAC level.
MITSUBISHI motor general AC servo amplifier MELSERVO-J3 series.
Need conversion unit MR-J3-CR55K) supporting the use of.
Rated output: 30kw.
Interface type: SSCNET type III fiber communication.
Power specification: three phase AC400V.
High speed serial communication between the SSCNET and the servo amplifier by using the fastest up to 0.44ms communication cycle,
A fully synchronous control system can be constructed.
It is only necessary to insert the special optical fiber into the joint to form SSCNET III network, which greatly reduces the wiring work and reduces the possibility of false wiring.
Due to the adoption of the optical fiber communication, the anti noise ability can be greatly improved and the long distance wiring of 50 meters (maximum 800 meters x 16 axes) can be realized.
A servo amplifier to meet the full closed loop control function MR-J3-B-RJ006.
Suitable for mechanical servo optimization and adjustment!
More advanced optimization adjustment function and control function to maximize mechanical properties.
Motor series: medium inertia, medium capacity.
Using a serial absolute / incremental encoder.
Rated output power: 3.5kw.
Rated speed: 3000rpm.
With a brake band.
Shaft end: straight shaft.
When the AC servo motor has no control voltage, only the pulsating magnetic field generated by the excitation winding is generated in the stator, and the rotor is still not moving MITSUBISHI MR-J3-DU30KB4.
When the control voltage is controlled, a rotating magnetic field is generated in the stator, and the rotor rotates in the direction of the rotating magnetic field,
In the case of constant load, the speed of the motor varies with the size of the control voltage,
When the phase of the control voltage is reversed, the servo motor will reverse MITSUBISHI MR-J3-DU30KB4 MR-J3-DU30KB4 MITSUBISHI general purpose AC servo amplifier MELSERVO-J2-Super series.
Rated output: 22.0kw.
Universal interface.
Voltage: 3 phase AC400V.
Super function, excellent performance.
High performance CPU integration, greatly improve product responsiveness.
Due to the application of high performance CPU, so that the response can be greatly improved.
Speed loop frequency response increased to more than 550HZ MITSUBISHI MR-J3-DU30KB4.
MR-J2-Super series is the best device for high speed positioning applications.
Easy adjustment.
Model adaptive control / advanced real time automatic tuning.
Mechanical analysis function.
Can analysis of the frequency characteristics of the mechanical system, the results can be easily set up "mechanical resonance suppression filter"
Mechanical simulation function MITSUBISHI SSCNET type III optical fiber communication driver.
The function can be realized without the actual replacement of the motor MITSUBISHI SSCNET type III optical fiber communication driver. Read mechanical analysis results to simulate the response of the user''s mechanical system.Type: MR-J series.
Rated output: 0.2KW.
Applicable motor series: HA-FF, HA-SE.
Voltage: single phase AC100V.
It is very helpful to improve the stability of the low speed control of the servo motor MITSUBISHI SSCNET type III optical fiber communication driver.
But there is no direct effect to improve the accuracy of position control.
There are, of course, software compensation that is similar to pitch compensation,
Can improve the physical resolution of the single lap, so as to improve the accuracy of positioning control.
This can be effectively used in the use of the robot controll of the indexing table MR-J3-DU30KB4.
It is also because of the application of splicing technology,
The rotary encoder will be more widely used in the high precision servo control in the harsh environment.
The use of rotary encoder with 224/ in the servo motor has been used in the servo motor MITSUBISHI MR-J3-DU30KB4.
Encoder serial communication system, the communication frequency can only be limited to 10M.
Using a serial absolute / incremental encoder.
Rated output power: 3.5kw.
Rated speed: 3000rpm.
With a brake band.
Shaft end: straight shaft.
When the AC servo motor has no control voltage, only the pulsating magnetic field generated by the excitation winding is generated in the stator, and the rotor is still not moving MITSUBISHI MR-J3-DU30KB4.
When the control voltage is controlled, a rotating magnetic field is generated in the stator, and the rotor rotates in the direction of the rotating magnetic field,
In the case of constant load, the speed of the motor varies with the size of the control voltage,
When the phase of the control voltage is reversed, the servo motor will reverse MITSUBISHI MR-J3-DU30KB4 MR-J3-DU30KB4 MITSUBISHI general purpose AC servo amplifier MELSERVO-J2-Super series.
Rated output: 22.0kw.
Universal interface.
Voltage: 3 phase AC400V.
Super function, excellent performance.
High performance CPU integration, greatly improve product responsiveness.
Due to the application of high performance CPU, so that the response can be greatly improved.
Speed loop frequency response increased to more than 550HZ MITSUBISHI MR-J3-DU30KB4.
MR-J2-Super series is the best device for high speed positioning applications.
Easy adjustment.
Model adaptive control / advanced real time automatic tuning.
Mechanical analysis function.
Can analysis of the frequency characteristics of the mechanical system, the results can be easily set up "mechanical resonance suppression filter"
Mechanical simulation function MITSUBISHI SSCNET type III optical fiber communication driver.
The function can be realized without the actual replacement of the motor MITSUBISHI SSCNET type III optical fiber communication driver. Read mechanical analysis results to simulate the response of the user''s mechanical system.Type: MR-J series.
Rated output: 0.2KW.
Applicable motor series: HA-FF, HA-SE.
Voltage: single phase AC100V.
It is very helpful to improve the stability of the low speed control of the servo motor MITSUBISHI SSCNET type III optical fiber communication driver.
But there is no direct effect to improve the accuracy of position control.
There are, of course, software compensation that is similar to pitch compensation,
Can improve the physical resolution of the single lap, so as to improve the accuracy of positioning control.
This can be effectively used in the use of the robot controll of the indexing table MR-J3-DU30KB4.
It is also because of the application of splicing technology,
The rotary encoder will be more widely used in the high precision servo control in the harsh environment.
The use of rotary encoder with 224/ in the servo motor has been used in the servo motor MITSUBISHI MR-J3-DU30KB4.
Encoder serial communication system, the communication frequency can only be limited to 10M.
...More relevant models >>>>
Last one: MITSUBISHI SSCNET type III optical fiber communication driver MR-J3-22KB4
next one: MITSUBISHI SSCNET type III optical fiber communication driver MR-J3-DU37KB4
Related download