Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> SGDV-____25 Type (Used by linear servo motor)
>> SGDV-R90A25A YASKAWA SGDV-R90A25A
SGDV-R90A25A YASKAWA SGDV-R90A25A
Brand:
Yaskawa
Name: Servo driver for linear servo motor
Model: SGDV-R90A25A
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.1kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
...More relevant models >>>>
Name: Servo driver for linear servo motor
Model: SGDV-R90A25A
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.1kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
Full closed loop module.
Maximum applicable motor capacity: 0.2kw.
Power supply voltage: single phase AC100V.
Interface: analog voltage, pulse sequence type (rotary servo motor).
Design sequence: A.
Hardware specification: base mounting type (standard).
Matching (software): no matching (standard) YASKAWA SGDV-R90A25A.
Matching (parameters): no matching (standard).
Optional modules: full closed loop module SGDV-R90A25A
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed on the side of the machine to realize the high precision and high response.
External encoder capable of corresponding high resolution (linear grating) YASKAWA SGDV-R90A25A. Sigma -V series servo motor SGMSV.
Rated output: 2.5kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with hold brake (DC24V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit) YASKAWA SGDV-R90A25A.
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above YASKAWA Servo driver for linear servo motor.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type YASKAWA Servo driver for linear servo motor.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection YASKAWA Servo driver for linear servo motor.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationServo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 0.3kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: B.
Shaft end: taper 1\/10, with parallel key.
Optional parts: no brake oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuitt,
Alarm can only turn off the main circuit power supply, easy to maintain SGDV-R90A25A.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 YASKAWA SGDV-R90A25A.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
Maximum applicable motor capacity: 0.2kw.
Power supply voltage: single phase AC100V.
Interface: analog voltage, pulse sequence type (rotary servo motor).
Design sequence: A.
Hardware specification: base mounting type (standard).
Matching (software): no matching (standard) YASKAWA SGDV-R90A25A.
Matching (parameters): no matching (standard).
Optional modules: full closed loop module SGDV-R90A25A
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed on the side of the machine to realize the high precision and high response.
External encoder capable of corresponding high resolution (linear grating) YASKAWA SGDV-R90A25A. Sigma -V series servo motor SGMSV.
Rated output: 2.5kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with hold brake (DC24V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit) YASKAWA SGDV-R90A25A.
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above YASKAWA Servo driver for linear servo motor.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type YASKAWA Servo driver for linear servo motor.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection YASKAWA Servo driver for linear servo motor.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationServo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 0.3kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: B.
Shaft end: taper 1\/10, with parallel key.
Optional parts: no brake oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuitt,
Alarm can only turn off the main circuit power supply, easy to maintain SGDV-R90A25A.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 YASKAWA SGDV-R90A25A.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
...More relevant models >>>>
Last one: Yaskawa Servo driver for linear servo motor SGDV-R70A25B002000
next one: Yaskawa Servo driver for linear servo motor SGDV-R90A25A002000
Related download