OMRON K3HB-XAD-ABCD1 AC100-240

Contact type: Standard load (250 VAC, 3 A; 30 VDC, 4 A).
Operation: Momentary operation (Self-resetting).
Case color: Black.
Output: DPDT.
Lighting: LED; 24 VDC.
Pushbutton color symbol: R.O.G.W.
Large Square-bodied Lighted.
Pushbutton Switches.
Excellent operating sensitivity.
Excellent illumination with even surface brightness OMRON .
Three-color models (green, orange, red; chameleon lighting) K3HB-XAD-ABCD1 AC100-240
included in lineup. Streamlined Communications from.
Temperature Controller to PLC.
The E5ZN Modular Temperature Controller is connected to,
the DeviceNet network.
The I/O link function allows setting and monitoring (e OMRON . g., of,
present values) for the E5ZN Modular Temperature Controller to,
be performed without communications programming .
Up to 16 E5ZN Modular Temperature Controllers can be,
connected to one Unit.
All the parameters for the E5ZN can be uploaded or download,
ed in one operation using DeviceNet Configurator. Ratings: Standard load; 4 A at 30 VDC.
Cable: VCTF oil-resistant cable *1 OMRON .
Actuator: Sealed roller plunger.
Cable length : 3 m.
Compact Limit Switch That''s Also .
Thin and Highly Sealed.
Approved by EN, UL, CSA, and CCC (Chinese standard).
(Ask your OMRON representative for information on approved models.)
Sealing characteristics that meet IEC IP67 degree of protection.
Triple-sealed construction:
Plunger section sealed via nitrile rubber packing seal and,
diaphragm; switch section sealed via nitrile rubber cap;
cable entrance sealed via encapsulating material.
Cable lengths of 3 and 5 m available on standard models.
Models also available with UL and CSA-certified cables.
Multiple mounting possible with Switches with Plungers.
Models with red LED indicators added to series for easy,
confirmation of operation.
(Set by default to light for non-operation.)
VCTF oil-resistant cables with CE marking.
(Applicable only to standard models.)Size: 48 x 96mm.
Category: power AC100 ~ 240V with.
Shell color: black.
Control output 1: output unit mode.
Control output 2: output unit mode.
Control mode: standard or heating cooling.
Auxiliary output points: 2 points.
Heater break, SSR fault detection function: single phase heater detection function.
Event entry point: 2.
Transfer output: -.
Remote SP:4 to 20mA input.
Communication: -.
New program type.
A new type of liquid crystal with high performance cost ratio is adopted in the 256 paragraph,
Visual angle, contrast can be improved.
Can be set up to 8 procedures (mode) x 32 (step) procedure.
High resolution 5 bit display / can display 0.01 degrees C.
High speed sampling period 60ms.
All models complete a variety of (to the thermocouple /Pt/ analog input switching), 1 machines to support a variety of sensors.
Also supports remote SP.
Add PV/SV state display function, to see the state of the thermostat
(automatic / manual, RUN/RESET, alarm), interactive display PV/SV.
Through the support software (VVer .4.3 CX-Thermo) makes the proceess of setting management becomes very
Simple use of simple computing functions (AND/OR logic and delay) to set the implementation of flexible contact output OMRON K3HB-XAD-ABCD1 AC100-240.
Through the infrared port can be carried out from the frronnt of the communication OMRON K3HB-XAD-ABCD1 AC100-240.
The control output ON/OFF times counting function can predict the fault of the internal relay of the temperature controller.
K3HB-XAD-ABCD1 AC100-240 Operation manual/Instructions/Model selection sample download link: /searchDownload.html?Search=K3HB-XAD-ABCD1 AC100-240&select=5