PFXZGPIUEXDM Proface PFXZGPIUEXDM

Standard cable for connecting GP3000H adapter and GP3000H.
Length: 5 meters. For connecting the GP3000H cable connector and the external output port, the output of the following connectors: serial: D-Sub 9 pin (convex), Ethernet: Jack RJ-45 (Modular), other: terminal block.GP4000E series entry-level programmable man-machine interface Proface PFXZGPIUEXDM.
Screen size: 10 inch widescreen.
Display type: TFT color LCD.
Resolution: 800 x 480 pixels (WVGA) PFXZGPIUEXDM
Display color number: 65536 color.
Backlight: LED.
Internal memory: EPROM FLASH 32 MB.
Backup memory: EPROM FLASH 128 KB.
Interface: RS-232C, RS-422/485, Ethernet, USB.
Voltage: DC24V.
Easy to direct Proface PFXZGPIUEXDM.
GP4000E full range of standard Ethernet, can be connected to a variety of industrial controller,
Such as PLC, motion controller, robot, vision sensor, etc . .
Expanding business.
All hardware can be used to create the required EX GP-Pro screen.
All hardware equipment using the same development platform, is conducive to the development of new business.
Reduce the burden of CPU PLC.
GP4000E series can use internal logic programming function (ladder diagram programming) to reduce the burden of CPU PLC Proface PFXZGPIUEXDM.
More humanized design.
USB1 (A Type) on the lock and prevent the U disk to drop the lock screw.
Sliding type battery cabin, so that more convenient to replace the battery.
3 communication interface (1 network port, serial port 2), not only can be directly connected with the PLC,
And can be directly connected with other controllers (SCM, thermostat),
Helps to reduce the cost of the modules to be added after connecting these controllers with PLC.
Take time for the bad production environment
Low power consumption, no heat sink holes, effectively reduce dust and water vapor intrusion.
PCBA reinforced coating process (fully automatic mechanical coating),
Farewell to the use of dust, humidity and other harsh environment concerns.AUX connector for external output (5 / set).10.4 inches (TFT), thin film for surface protection of man-machine interface from fingerprints, water droplets, dust and oil pollution (5 / set).PNP output type.
Display size: 5.7 inches.
Resolution: 320 x 240 pixels (QVGA).
LCD: monochrome.
Color: 16 levels of gray.
Ethernet interface: No.
Serial port: 1.
CANopen interface: No.
USB (host):1.
USB (device): none.
Built in DIO input: 16 points.
Built in DIO output: 16 points.
Built in AIO input: No.
Built in AIO output: No.
Common DIO:2 point high speed counter (with synchronous output) pulse capture input, pulse output, PWM output.
Special DIO: No.
Expansion module EX module: up to 3.
Expansion module CANopen module: 63 stations.
Controller memory size: EPROM 132KB FLASH (equivalent to 15000 steps (up to 60000 steps).
Integrated design.
Adopt integrative design, compact structure,
When the installation is only required to open a hole in the panel 22mm.
The display module or the control module can be easily replaced when the fault is eliminated.
Using remote monitoring software GP-Viewer or data acquisition software EX Pro-Server,
Can easily monitor the production scene of the man-machine interface screen, or release production orders and real-time data collection.
Flexible installation.
The control module can be installed on the DIN guide rail by using the split installation cable,
And the display module is installed in other locations.
Display module occupies a small space, even if the space is limited, but also can be flexible to install.
Connect various control devices.
Pro-face human machine interface can be connected to a variety of industrial controllers, including PLC, motion controller, robot and other equipment.
Remote HMI Pro-face.
Natural connection production line and tablet PC or smart phone. By adding APP,
True implementation of mobile operations without loss of any operational performance.
Directly confirm the cause of the failure of the phone, as far as possible not to the scene on the recovery of the machine running.
In order to meet the needs of users for small control devices, Pro-face integrated control and operation functions in the human computer interface.
In short, is to indicate the lights, instruments and other display devices and switches, buttons and other operational functions to integrate into a compact PLC.
In addition to reducing wiring and saving space, the design also greatly reduces the use of electrical components,
Which ensures the long service life of the equipment.
The compact models are equipped with standard I/O, and they can be used as a special I/O.
High / low pulse with maximum 100kHz and maximum 65kHz of the high speed counter can be achieved by the advanced control.
Strong I/O interface not only supports the need to switch and indicator light equipment, but also supports the need for sophisticated positioning of complex equipment.
CANopen network
LT4000M supports data exchange with a variety of remote devices through the CANopen, easy to achieve economic and easy to use system design.
Can choose standard I/O module, also can choose action or control module and other more advanced products in complex application.
Use EX GP-Pro to easily test and debug the project.
EX GP-Pro simulation is a kind of offline simulation function, with the help off this function,

No need to connect the man-machine interface, you can test the operation of the screen and the logic program PFXZGPIUEXDM.
Compact size.
The volume is small but the display is fresh and bright, can create a rich and readable operation picture.

Thhe control function of the whole and the digital I/O, analog I/O, analog temperature input and USB, serial port and Ethernet communication interface PFXZGPIUEXDM.
PFXZGPIUEXDM Operation manual/Instructions/Model selection sample download link: /searchDownload.html?Search=PFXZGPIUEXDM&select=5